linux/drivers/usb/atm/Makefile

#
# Makefile for USB ATM/xDSL drivers
#

obj-$(CONFIG_USB_CXACRU)	+= cxacru.o
obj-$(CONFIG_USB_SPEEDTOUCH)	+= speedtch.o
obj-$(CONFIG_USB_UEAGLEATM)	+= ueagle-atm.o
obj-$(CONFIG_USB_ATM)		+= usbatm.o
obj-$(CONFIG_USB_XUSBATM)	+= xusbatm.o

ifeq ($(CONFIG_USB_DEBUG),y)
EXTRA_CFLAGS += -DDEBUG
endif
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 06:20:36 +08:00			`#`
[PATCH] USB ATM: bits and bobs Makefile and Kconfig entries for the new drivers. Signed-off-by: Duncan Sands <baldrick@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 2005-05-12 02:15:37 +08:00			`# Makefile for USB ATM/xDSL drivers`
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 06:20:36 +08:00			`#`

[PATCH] USB ATM: bits and bobs Makefile and Kconfig entries for the new drivers. Signed-off-by: Duncan Sands <baldrick@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 2005-05-12 02:15:37 +08:00			`obj-$(CONFIG_USB_CXACRU) += cxacru.o`
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 06:20:36 +08:00			`obj-$(CONFIG_USB_SPEEDTOUCH) += speedtch.o`
[PATCH] USB: Eagle and ADI 930 usb adsl modem driver A driver for USB ADSL modems based on the ADI eagle chipset using the usb_atm infrastructure. The managing part was taken from bsd ueagle driver, other parts were written from scratch. The driver uses the in-kernel firmware loader : - to load a first usb firmware when the modem is in pre-firmware state - to load the dsp firmware that are swapped in host memory. - to load CMV (configuration and management variables) when the modem boot. (We can't use options or sysfs for this as there many possible values. See https://mail.gna.org/public/eagleusb-dev/2005-04/msg00031.html for a description of some) - to load fpga code for 930 chipset. The device had 4 endpoints : * 2 for data (use by usbatm). The incoming endpoint could be iso or bulk. The modem seems buggy and produce lot's of atm errors when using it in bulk mode for speed > 3Mbps, so iso endpoint is need for speed > 3Mbps. At the moment iso endpoint need a patched usbatm library and for this reason is not included in this patch. * One bulk endpoint for uploading dsp firmware * One irq endpoint that notices the driver - if we need to upload a page of the dsp firmware - an ack for read or write CMV and the value (for the read case). If order to make the driver cleaner, we design synchronous (read\|write)_cmv : -send a synchronous control message to the modem -wait for an ack or a timeout -return the value if needed. In order to run these synchronous usb messages we need a kernel thread. The driver has been tested with sagem fast 800 modems with different eagle chipset revision and with ADI 930 since April 2005. Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 2005-11-08 06:27:13 +08:00			`obj-$(CONFIG_USB_UEAGLEATM) += ueagle-atm.o`
[PATCH] USB ATM: bits and bobs Makefile and Kconfig entries for the new drivers. Signed-off-by: Duncan Sands <baldrick@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 2005-05-12 02:15:37 +08:00			`obj-$(CONFIG_USB_ATM) += usbatm.o`
			`obj-$(CONFIG_USB_XUSBATM) += xusbatm.o`
[PATCH] USB: move CONFIG_USB_DEBUG checks into the Makefile This lets us remove a lot of code in the drivers that were all checking the same thing. It also found some bugs in a few of the drivers, which has been fixed up. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org> 2005-11-18 01:48:09 +08:00
			`ifeq ($(CONFIG_USB_DEBUG),y)`
			`EXTRA_CFLAGS += -DDEBUG`
			`endif`