linux/arch/powerpc/kernel/vector.S

331 lines
6.6 KiB
ArmAsm
Raw Normal View History

License cleanup: add SPDX GPL-2.0 license identifier to files with no license Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 22:07:57 +08:00
/* SPDX-License-Identifier: GPL-2.0 */
#include <asm/processor.h>
#include <asm/ppc_asm.h>
#include <asm/reg.h>
#include <asm/asm-offsets.h>
#include <asm/cputable.h>
#include <asm/thread_info.h>
#include <asm/page.h>
#include <asm/ptrace.h>
#include <asm/export.h>
#include <asm/asm-compat.h>
/*
* Load state from memory into VMX registers including VSCR.
* Assumes the caller has enabled VMX in the MSR.
*/
_GLOBAL(load_vr_state)
li r4,VRSTATE_VSCR
lvx v0,r4,r3
mtvscr v0
REST_32VRS(0,r4,r3)
blr
EXPORT_SYMBOL(load_vr_state)
/*
* Store VMX state into memory, including VSCR.
* Assumes the caller has enabled VMX in the MSR.
*/
_GLOBAL(store_vr_state)
SAVE_32VRS(0, r4, r3)
mfvscr v0
li r4, VRSTATE_VSCR
stvx v0, r4, r3
blr
EXPORT_SYMBOL(store_vr_state)
/*
* Disable VMX for the task which had it previously,
* and save its vector registers in its thread_struct.
* Enables the VMX for use in the kernel on return.
* On SMP we know the VMX is free, since we give it up every
* switch (ie, no lazy save of the vector registers).
*
* Note that on 32-bit this can only use registers that will be
* restored by fast_exception_return, i.e. r3 - r6, r10 and r11.
*/
_GLOBAL(load_up_altivec)
mfmsr r5 /* grab the current MSR */
oris r5,r5,MSR_VEC@h
MTMSRD(r5) /* enable use of AltiVec now */
isync
/*
* While userspace in general ignores VRSAVE, glibc uses it as a boolean
* to optimise userspace context save/restore. Whenever we take an
* altivec unavailable exception we must set VRSAVE to something non
* zero. Set it to all 1s. See also the programming note in the ISA.
*/
mfspr r4,SPRN_VRSAVE
cmpwi 0,r4,0
bne+ 1f
li r4,-1
mtspr SPRN_VRSAVE,r4
1:
/* enable use of VMX after return */
#ifdef CONFIG_PPC32
mfspr r5,SPRN_SPRG_THREAD /* current task's THREAD (phys) */
oris r9,r9,MSR_VEC@h
#else
ld r4,PACACURRENT(r13)
addi r5,r4,THREAD /* Get THREAD */
oris r12,r12,MSR_VEC@h
std r12,_MSR(r1)
#endif
powerpc: Restore FPU/VEC/VSX if previously used Currently the FPU, VEC and VSX facilities are lazily loaded. This is not a problem unless a process is using these facilities. Modern versions of GCC are very good at automatically vectorising code, new and modernised workloads make use of floating point and vector facilities, even the kernel makes use of vectorised memcpy. All this combined greatly increases the cost of a syscall since the kernel uses the facilities sometimes even in syscall fast-path making it increasingly common for a thread to take an *_unavailable exception soon after a syscall, not to mention potentially taking all three. The obvious overcompensation to this problem is to simply always load all the facilities on every exit to userspace. Loading up all FPU, VEC and VSX registers every time can be expensive and if a workload does avoid using them, it should not be forced to incur this penalty. An 8bit counter is used to detect if the registers have been used in the past and the registers are always loaded until the value wraps to back to zero. Several versions of the assembly in entry_64.S were tested: 1. Always calling C. 2. Performing a common case check and then calling C. 3. A complex check in asm. After some benchmarking it was determined that avoiding C in the common case is a performance benefit (option 2). The full check in asm (option 3) greatly complicated that codepath for a negligible performance gain and the trade-off was deemed not worth it. Signed-off-by: Cyril Bur <cyrilbur@gmail.com> [mpe: Move load_vec in the struct to fill an existing hole, reword change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> fixup
2016-02-29 14:53:47 +08:00
/* Don't care if r4 overflows, this is desired behaviour */
lbz r4,THREAD_LOAD_VEC(r5)
addi r4,r4,1
stb r4,THREAD_LOAD_VEC(r5)
addi r6,r5,THREAD_VRSTATE
li r4,1
li r10,VRSTATE_VSCR
stw r4,THREAD_USED_VR(r5)
lvx v0,r10,r6
mtvscr v0
REST_32VRS(0,r4,r6)
/* restore registers and return */
blr
/*
* save_altivec(tsk)
* Save the vector registers to its thread_struct
*/
_GLOBAL(save_altivec)
addi r3,r3,THREAD /* want THREAD of task */
PPC_LL r7,THREAD_VRSAVEAREA(r3)
PPC_LL r5,PT_REGS(r3)
PPC_LCMPI 0,r7,0
bne 2f
addi r7,r3,THREAD_VRSTATE
2: SAVE_32VRS(0,r4,r7)
mfvscr v0
li r4,VRSTATE_VSCR
stvx v0,r4,r7
blr
#ifdef CONFIG_VSX
#ifdef CONFIG_PPC32
#error This asm code isn't ready for 32-bit kernels
#endif
/*
* load_up_vsx(unused, unused, tsk)
* Disable VSX for the task which had it previously,
* and save its vector registers in its thread_struct.
* Reuse the fp and vsx saves, but first check to see if they have
* been saved already.
*/
_GLOBAL(load_up_vsx)
/* Load FP and VSX registers if they haven't been done yet */
andi. r5,r12,MSR_FP
beql+ load_up_fpu /* skip if already loaded */
andis. r5,r12,MSR_VEC@h
beql+ load_up_altivec /* skip if already loaded */
ld r4,PACACURRENT(r13)
addi r4,r4,THREAD /* Get THREAD */
li r6,1
stw r6,THREAD_USED_VSR(r4) /* ... also set thread used vsr */
/* enable use of VSX after return */
oris r12,r12,MSR_VSX@h
std r12,_MSR(r1)
b fast_exception_return
#endif /* CONFIG_VSX */
/*
* The routines below are in assembler so we can closely control the
* usage of floating-point registers. These routines must be called
* with preempt disabled.
*/
#ifdef CONFIG_PPC32
.data
fpzero:
.long 0
fpone:
.long 0x3f800000 /* 1.0 in single-precision FP */
fphalf:
.long 0x3f000000 /* 0.5 in single-precision FP */
#define LDCONST(fr, name) \
lis r11,name@ha; \
lfs fr,name@l(r11)
#else
.section ".toc","aw"
fpzero:
.tc FD_0_0[TC],0
fpone:
.tc FD_3ff00000_0[TC],0x3ff0000000000000 /* 1.0 */
fphalf:
.tc FD_3fe00000_0[TC],0x3fe0000000000000 /* 0.5 */
#define LDCONST(fr, name) \
lfd fr,name@toc(r2)
#endif
.text
/*
* Internal routine to enable floating point and set FPSCR to 0.
* Don't call it from C; it doesn't use the normal calling convention.
*/
fpenable:
#ifdef CONFIG_PPC32
stwu r1,-64(r1)
#else
stdu r1,-64(r1)
#endif
mfmsr r10
ori r11,r10,MSR_FP
mtmsr r11
isync
stfd fr0,24(r1)
stfd fr1,16(r1)
stfd fr31,8(r1)
LDCONST(fr1, fpzero)
mffs fr31
MTFSF_L(fr1)
blr
fpdisable:
mtlr r12
MTFSF_L(fr31)
lfd fr31,8(r1)
lfd fr1,16(r1)
lfd fr0,24(r1)
mtmsr r10
isync
addi r1,r1,64
blr
/*
* Vector add, floating point.
*/
_GLOBAL(vaddfp)
mflr r12
bl fpenable
li r0,4
mtctr r0
li r6,0
1: lfsx fr0,r4,r6
lfsx fr1,r5,r6
fadds fr0,fr0,fr1
stfsx fr0,r3,r6
addi r6,r6,4
bdnz 1b
b fpdisable
/*
* Vector subtract, floating point.
*/
_GLOBAL(vsubfp)
mflr r12
bl fpenable
li r0,4
mtctr r0
li r6,0
1: lfsx fr0,r4,r6
lfsx fr1,r5,r6
fsubs fr0,fr0,fr1
stfsx fr0,r3,r6
addi r6,r6,4
bdnz 1b
b fpdisable
/*
* Vector multiply and add, floating point.
*/
_GLOBAL(vmaddfp)
mflr r12
bl fpenable
stfd fr2,32(r1)
li r0,4
mtctr r0
li r7,0
1: lfsx fr0,r4,r7
lfsx fr1,r5,r7
lfsx fr2,r6,r7
fmadds fr0,fr0,fr2,fr1
stfsx fr0,r3,r7
addi r7,r7,4
bdnz 1b
lfd fr2,32(r1)
b fpdisable
/*
* Vector negative multiply and subtract, floating point.
*/
_GLOBAL(vnmsubfp)
mflr r12
bl fpenable
stfd fr2,32(r1)
li r0,4
mtctr r0
li r7,0
1: lfsx fr0,r4,r7
lfsx fr1,r5,r7
lfsx fr2,r6,r7
fnmsubs fr0,fr0,fr2,fr1
stfsx fr0,r3,r7
addi r7,r7,4
bdnz 1b
lfd fr2,32(r1)
b fpdisable
/*
* Vector reciprocal estimate. We just compute 1.0/x.
* r3 -> destination, r4 -> source.
*/
_GLOBAL(vrefp)
mflr r12
bl fpenable
li r0,4
LDCONST(fr1, fpone)
mtctr r0
li r6,0
1: lfsx fr0,r4,r6
fdivs fr0,fr1,fr0
stfsx fr0,r3,r6
addi r6,r6,4
bdnz 1b
b fpdisable
/*
* Vector reciprocal square-root estimate, floating point.
* We use the frsqrte instruction for the initial estimate followed
* by 2 iterations of Newton-Raphson to get sufficient accuracy.
* r3 -> destination, r4 -> source.
*/
_GLOBAL(vrsqrtefp)
mflr r12
bl fpenable
stfd fr2,32(r1)
stfd fr3,40(r1)
stfd fr4,48(r1)
stfd fr5,56(r1)
li r0,4
LDCONST(fr4, fpone)
LDCONST(fr5, fphalf)
mtctr r0
li r6,0
1: lfsx fr0,r4,r6
frsqrte fr1,fr0 /* r = frsqrte(s) */
fmuls fr3,fr1,fr0 /* r * s */
fmuls fr2,fr1,fr5 /* r * 0.5 */
fnmsubs fr3,fr1,fr3,fr4 /* 1 - s * r * r */
fmadds fr1,fr2,fr3,fr1 /* r = r + 0.5 * r * (1 - s * r * r) */
fmuls fr3,fr1,fr0 /* r * s */
fmuls fr2,fr1,fr5 /* r * 0.5 */
fnmsubs fr3,fr1,fr3,fr4 /* 1 - s * r * r */
fmadds fr1,fr2,fr3,fr1 /* r = r + 0.5 * r * (1 - s * r * r) */
stfsx fr1,r3,r6
addi r6,r6,4
bdnz 1b
lfd fr5,56(r1)
lfd fr4,48(r1)
lfd fr3,40(r1)
lfd fr2,32(r1)
b fpdisable