linux/arch/powerpc/xmon/Makefile

# Makefile for xmon

subdir-ccflags-$(CONFIG_PPC_WERROR) := -Werror

GCOV_PROFILE := n

ccflags-$(CONFIG_PPC64) := $(NO_MINIMAL_TOC)

obj-y			+= xmon.o nonstdio.o

ifdef CONFIG_XMON_DISASSEMBLY
obj-y			+= ppc-dis.o ppc-opc.o
obj-$(CONFIG_SPU_BASE)	+= spu-dis.o spu-opc.o
endif
powerpc: Merge xmon The merged version follows the ppc64 version pretty closely mostly, and in fact ARCH=ppc64 now uses the arch/powerpc/xmon version. The main difference for ppc64 is that the 'p' command to call show_state (which was always pretty dodgy) has been replaced by the ppc32 'p' command, which calls a given procedure (so in fact the old 'p' command behaviour can be achieved with 'p $show_state'). Signed-off-by: Paul Mackerras <paulus@samba.org> 2005-10-28 20:53:37 +08:00			`# Makefile for xmon`

powerpc: Add configurable -Werror for arch/powerpc Add the option to build the code under arch/powerpc with -Werror. The intention is to make it harder for people to inadvertantly introduce warnings in the arch/powerpc code. It needs to be configurable so that if a warning is introduced, people can easily work around it while it's being fixed. The option is a negative, ie. don't enable -Werror, so that it will be turned on for allyes and allmodconfig builds. The default is n, in the hope that developers will build with -Werror, that will probably lead to some build breaks, I am prepared to be flamed. It's not enabled for math-emu, which is a steaming pile of warnings. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> 2009-06-10 04:48:51 +08:00			`subdir-ccflags-$(CONFIG_PPC_WERROR) := -Werror`

powerpc: Enable GCOV Make it possible to enable GCOV code coverage measurement on powerpc. Lightly tested on 64-bit, seems to work as expected. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> 2009-08-10 03:02:51 +08:00			`GCOV_PROFILE := n`

powerpc: Build kernel with -mcmodel=medium Finally remove the two level TOC and build with -mcmodel=medium. Unfortunately we can't build modules with -mcmodel=medium due to the tricks the kernel module loader plays with percpu data: # -mcmodel=medium breaks modules because it uses 32bit offsets from # the TOC pointer to create pointers where possible. Pointers into the # percpu data area are created by this method. # # The kernel module loader relocates the percpu data section from the # original location (starting with 0xd...) to somewhere in the base # kernel percpu data space (starting with 0xc...). We need a full # 64bit relocation for this to work, hence -mcmodel=large. On older kernels we fall back to the two level TOC (-mminimal-toc) Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> 2012-11-27 01:41:08 +08:00			`ccflags-$(CONFIG_PPC64) := $(NO_MINIMAL_TOC)`
[POWERPC] Make xmon disassembly optional While adding spu disassembly support it struck me that we're actually carrying quite a lot of code around, just to do disassembly in the case of a crash. While on large systems it's not an issue, on smaller ones it might be nice to have xmon - but without the weight of the disassembly support. For a Cell build this saves ~230KB (!), and for pSeries ~195KB. We still support the 'di' and 'sdi' commands, however they just dump the instruction in hex. Move the definitions into a header to clean xmon.c just a tiny bit. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> 2006-11-23 07:46:45 +08:00
powerpc/xmon: Merge start.c into nonstdio.c The routines in start.c are only ever called from nonstdio.c, so if we move them in there they can become static which is nice. I suspect the idea behind the separation was that start.c could be replaced in order to build xmon in userland. If anyone still cares about doing that we could handle that with an ifdef or two. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> 2012-10-09 12:20:32 +08:00			`obj-y += xmon.o nonstdio.o`
[POWERPC] Make xmon disassembly optional While adding spu disassembly support it struck me that we're actually carrying quite a lot of code around, just to do disassembly in the case of a crash. While on large systems it's not an issue, on smaller ones it might be nice to have xmon - but without the weight of the disassembly support. For a Cell build this saves ~230KB (!), and for pSeries ~195KB. We still support the 'di' and 'sdi' commands, however they just dump the instruction in hex. Move the definitions into a header to clean xmon.c just a tiny bit. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> 2006-11-23 07:46:45 +08:00
			`ifdef CONFIG_XMON_DISASSEMBLY`
			`obj-y += ppc-dis.o ppc-opc.o`
[POWERPC] cell: fix building without spufs It may be desireable to build a kernel for cell without spufs, e.g. as the initial kboot kernel. This requires that the SPU specific parts of the core dump and the xmon code depend on CONFIG_SPU_BASE instead of CONFIG_PPC_CELL. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> 2006-11-28 02:18:55 +08:00			`obj-$(CONFIG_SPU_BASE) += spu-dis.o spu-opc.o`
[POWERPC] Make xmon disassembly optional While adding spu disassembly support it struck me that we're actually carrying quite a lot of code around, just to do disassembly in the case of a crash. While on large systems it's not an issue, on smaller ones it might be nice to have xmon - but without the weight of the disassembly support. For a Cell build this saves ~230KB (!), and for pSeries ~195KB. We still support the 'di' and 'sdi' commands, however they just dump the instruction in hex. Move the definitions into a header to clean xmon.c just a tiny bit. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> 2006-11-23 07:46:45 +08:00			`endif`