linux/drivers/media/i2c/ov2740.c

1452 lines
33 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0
// Copyright (c) 2020 Intel Corporation.
#include <asm/unaligned.h>
#include <linux/acpi.h>
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/gpio/consumer.h>
#include <linux/i2c.h>
#include <linux/module.h>
#include <linux/pm_runtime.h>
#include <linux/nvmem-provider.h>
#include <linux/regmap.h>
#include <media/v4l2-ctrls.h>
#include <media/v4l2-device.h>
#include <media/v4l2-fwnode.h>
#define OV2740_LINK_FREQ_360MHZ 360000000ULL
#define OV2740_LINK_FREQ_180MHZ 180000000ULL
#define OV2740_SCLK 72000000LL
#define OV2740_MCLK 19200000
#define OV2740_DATA_LANES 2
#define OV2740_RGB_DEPTH 10
#define OV2740_REG_CHIP_ID 0x300a
#define OV2740_CHIP_ID 0x2740
#define OV2740_REG_MODE_SELECT 0x0100
#define OV2740_MODE_STANDBY 0x00
#define OV2740_MODE_STREAMING 0x01
/* vertical-timings from sensor */
#define OV2740_REG_VTS 0x380e
/* horizontal-timings from sensor */
#define OV2740_REG_HTS 0x380c
/* Exposure controls from sensor */
#define OV2740_REG_EXPOSURE 0x3500
#define OV2740_EXPOSURE_MIN 4
#define OV2740_EXPOSURE_MAX_MARGIN 8
#define OV2740_EXPOSURE_STEP 1
/* Analog gain controls from sensor */
#define OV2740_REG_ANALOG_GAIN 0x3508
#define OV2740_ANAL_GAIN_MIN 128
#define OV2740_ANAL_GAIN_MAX 1983
#define OV2740_ANAL_GAIN_STEP 1
/* Digital gain controls from sensor */
#define OV2740_REG_MWB_R_GAIN 0x500a
#define OV2740_REG_MWB_G_GAIN 0x500c
#define OV2740_REG_MWB_B_GAIN 0x500e
#define OV2740_DGTL_GAIN_MIN 1024
#define OV2740_DGTL_GAIN_MAX 4095
#define OV2740_DGTL_GAIN_STEP 1
#define OV2740_DGTL_GAIN_DEFAULT 1024
/* Test Pattern Control */
#define OV2740_REG_TEST_PATTERN 0x5040
#define OV2740_TEST_PATTERN_ENABLE BIT(7)
#define OV2740_TEST_PATTERN_BAR_SHIFT 2
/* Group Access */
#define OV2740_REG_GROUP_ACCESS 0x3208
#define OV2740_GROUP_HOLD_START 0x0
#define OV2740_GROUP_HOLD_END 0x10
#define OV2740_GROUP_HOLD_LAUNCH 0xa0
/* ISP CTRL00 */
#define OV2740_REG_ISP_CTRL00 0x5000
/* ISP CTRL01 */
#define OV2740_REG_ISP_CTRL01 0x5001
/* Customer Addresses: 0x7010 - 0x710F */
#define CUSTOMER_USE_OTP_SIZE 0x100
/* OTP registers from sensor */
#define OV2740_REG_OTP_CUSTOMER 0x7010
struct nvm_data {
struct nvmem_device *nvmem;
struct regmap *regmap;
char *nvm_buffer;
};
enum {
OV2740_LINK_FREQ_360MHZ_INDEX,
OV2740_LINK_FREQ_180MHZ_INDEX,
};
struct ov2740_reg {
u16 address;
u8 val;
};
struct ov2740_reg_list {
u32 num_of_regs;
const struct ov2740_reg *regs;
};
struct ov2740_link_freq_config {
const struct ov2740_reg_list reg_list;
};
struct ov2740_mode {
/* Frame width in pixels */
u32 width;
/* Frame height in pixels */
u32 height;
/* Horizontal timining size */
u32 hts;
/* Default vertical timining size */
u32 vts_def;
/* Min vertical timining size */
u32 vts_min;
/* Max vertical timining size */
u32 vts_max;
/* Link frequency needed for this resolution */
u32 link_freq_index;
/* Sensor register settings for this resolution */
const struct ov2740_reg_list reg_list;
};
static const struct ov2740_reg mipi_data_rate_720mbps[] = {
{0x0302, 0x4b},
{0x030d, 0x4b},
{0x030e, 0x02},
{0x030a, 0x01},
{0x0312, 0x11},
};
static const struct ov2740_reg mipi_data_rate_360mbps[] = {
{0x0302, 0x4b},
{0x0303, 0x01},
{0x030d, 0x4b},
{0x030e, 0x02},
{0x030a, 0x01},
{0x0312, 0x11},
{0x4837, 0x2c},
};
static const struct ov2740_reg mode_1932x1092_regs_360mhz[] = {
{0x3000, 0x00},
{0x3018, 0x32},
{0x3031, 0x0a},
{0x3080, 0x08},
{0x3083, 0xB4},
{0x3103, 0x00},
{0x3104, 0x01},
{0x3106, 0x01},
{0x3500, 0x00},
{0x3501, 0x44},
{0x3502, 0x40},
{0x3503, 0x88},
{0x3507, 0x00},
{0x3508, 0x00},
{0x3509, 0x80},
{0x350c, 0x00},
{0x350d, 0x80},
{0x3510, 0x00},
{0x3511, 0x00},
{0x3512, 0x20},
{0x3632, 0x00},
{0x3633, 0x10},
{0x3634, 0x10},
{0x3635, 0x10},
{0x3645, 0x13},
{0x3646, 0x81},
{0x3636, 0x10},
{0x3651, 0x0a},
{0x3656, 0x02},
{0x3659, 0x04},
{0x365a, 0xda},
{0x365b, 0xa2},
{0x365c, 0x04},
{0x365d, 0x1d},
{0x365e, 0x1a},
{0x3662, 0xd7},
{0x3667, 0x78},
{0x3669, 0x0a},
{0x366a, 0x92},
{0x3700, 0x54},
{0x3702, 0x10},
{0x3706, 0x42},
{0x3709, 0x30},
{0x370b, 0xc2},
{0x3714, 0x63},
{0x3715, 0x01},
{0x3716, 0x00},
{0x371a, 0x3e},
{0x3732, 0x0e},
{0x3733, 0x10},
{0x375f, 0x0e},
{0x3768, 0x30},
{0x3769, 0x44},
{0x376a, 0x22},
{0x377b, 0x20},
{0x377c, 0x00},
{0x377d, 0x0c},
{0x3798, 0x00},
{0x37a1, 0x55},
{0x37a8, 0x6d},
{0x37c2, 0x04},
{0x37c5, 0x00},
{0x37c8, 0x00},
{0x3800, 0x00},
{0x3801, 0x00},
{0x3802, 0x00},
{0x3803, 0x00},
{0x3804, 0x07},
{0x3805, 0x8f},
{0x3806, 0x04},
{0x3807, 0x47},
{0x3808, 0x07},
{0x3809, 0x88},
{0x380a, 0x04},
{0x380b, 0x40},
{0x380c, 0x04},
{0x380d, 0x38},
{0x380e, 0x04},
{0x380f, 0x60},
{0x3810, 0x00},
{0x3811, 0x04},
{0x3812, 0x00},
{0x3813, 0x04},
{0x3814, 0x01},
{0x3815, 0x01},
{0x3820, 0x80},
{0x3821, 0x46},
{0x3822, 0x84},
{0x3829, 0x00},
{0x382a, 0x01},
{0x382b, 0x01},
{0x3830, 0x04},
{0x3836, 0x01},
{0x3837, 0x08},
{0x3839, 0x01},
{0x383a, 0x00},
{0x383b, 0x08},
{0x383c, 0x00},
{0x3f0b, 0x00},
{0x4001, 0x20},
{0x4009, 0x07},
{0x4003, 0x10},
{0x4010, 0xe0},
{0x4016, 0x00},
{0x4017, 0x10},
{0x4044, 0x02},
{0x4304, 0x08},
{0x4307, 0x30},
{0x4320, 0x80},
{0x4322, 0x00},
{0x4323, 0x00},
{0x4324, 0x00},
{0x4325, 0x00},
{0x4326, 0x00},
{0x4327, 0x00},
{0x4328, 0x00},
{0x4329, 0x00},
{0x432c, 0x03},
{0x432d, 0x81},
{0x4501, 0x84},
{0x4502, 0x40},
{0x4503, 0x18},
{0x4504, 0x04},
{0x4508, 0x02},
{0x4601, 0x10},
{0x4800, 0x00},
{0x4816, 0x52},
{0x4837, 0x16},
{0x5000, 0x7f},
{0x5001, 0x00},
{0x5005, 0x38},
{0x501e, 0x0d},
{0x5040, 0x00},
{0x5901, 0x00},
{0x3800, 0x00},
{0x3801, 0x00},
{0x3802, 0x00},
{0x3803, 0x00},
{0x3804, 0x07},
{0x3805, 0x8f},
{0x3806, 0x04},
{0x3807, 0x47},
{0x3808, 0x07},
{0x3809, 0x8c},
{0x380a, 0x04},
{0x380b, 0x44},
{0x3810, 0x00},
{0x3811, 0x00},
{0x3812, 0x00},
{0x3813, 0x01},
};
static const struct ov2740_reg mode_1932x1092_regs_180mhz[] = {
{0x3000, 0x00},
{0x3018, 0x32}, /* 0x32 for 2 lanes, 0x12 for 1 lane */
{0x3031, 0x0a},
{0x3080, 0x08},
{0x3083, 0xB4},
{0x3103, 0x00},
{0x3104, 0x01},
{0x3106, 0x01},
{0x3500, 0x00},
{0x3501, 0x44},
{0x3502, 0x40},
{0x3503, 0x88},
{0x3507, 0x00},
{0x3508, 0x00},
{0x3509, 0x80},
{0x350c, 0x00},
{0x350d, 0x80},
{0x3510, 0x00},
{0x3511, 0x00},
{0x3512, 0x20},
{0x3632, 0x00},
{0x3633, 0x10},
{0x3634, 0x10},
{0x3635, 0x10},
{0x3645, 0x13},
{0x3646, 0x81},
{0x3636, 0x10},
{0x3651, 0x0a},
{0x3656, 0x02},
{0x3659, 0x04},
{0x365a, 0xda},
{0x365b, 0xa2},
{0x365c, 0x04},
{0x365d, 0x1d},
{0x365e, 0x1a},
{0x3662, 0xd7},
{0x3667, 0x78},
{0x3669, 0x0a},
{0x366a, 0x92},
{0x3700, 0x54},
{0x3702, 0x10},
{0x3706, 0x42},
{0x3709, 0x30},
{0x370b, 0xc2},
{0x3714, 0x63},
{0x3715, 0x01},
{0x3716, 0x00},
{0x371a, 0x3e},
{0x3732, 0x0e},
{0x3733, 0x10},
{0x375f, 0x0e},
{0x3768, 0x30},
{0x3769, 0x44},
{0x376a, 0x22},
{0x377b, 0x20},
{0x377c, 0x00},
{0x377d, 0x0c},
{0x3798, 0x00},
{0x37a1, 0x55},
{0x37a8, 0x6d},
{0x37c2, 0x04},
{0x37c5, 0x00},
{0x37c8, 0x00},
{0x3800, 0x00},
{0x3801, 0x00},
{0x3802, 0x00},
{0x3803, 0x00},
{0x3804, 0x07},
{0x3805, 0x8f},
{0x3806, 0x04},
{0x3807, 0x47},
{0x3808, 0x07},
{0x3809, 0x88},
{0x380a, 0x04},
{0x380b, 0x40},
{0x380c, 0x08},
{0x380d, 0x70},
{0x380e, 0x04},
{0x380f, 0x56},
{0x3810, 0x00},
{0x3811, 0x04},
{0x3812, 0x00},
{0x3813, 0x04},
{0x3814, 0x01},
{0x3815, 0x01},
{0x3820, 0x80},
{0x3821, 0x46},
{0x3822, 0x84},
{0x3829, 0x00},
{0x382a, 0x01},
{0x382b, 0x01},
{0x3830, 0x04},
{0x3836, 0x01},
{0x3837, 0x08},
{0x3839, 0x01},
{0x383a, 0x00},
{0x383b, 0x08},
{0x383c, 0x00},
{0x3f0b, 0x00},
{0x4001, 0x20},
{0x4009, 0x07},
{0x4003, 0x10},
{0x4010, 0xe0},
{0x4016, 0x00},
{0x4017, 0x10},
{0x4044, 0x02},
{0x4304, 0x08},
{0x4307, 0x30},
{0x4320, 0x80},
{0x4322, 0x00},
{0x4323, 0x00},
{0x4324, 0x00},
{0x4325, 0x00},
{0x4326, 0x00},
{0x4327, 0x00},
{0x4328, 0x00},
{0x4329, 0x00},
{0x432c, 0x03},
{0x432d, 0x81},
{0x4501, 0x84},
{0x4502, 0x40},
{0x4503, 0x18},
{0x4504, 0x04},
{0x4508, 0x02},
{0x4601, 0x10},
{0x4800, 0x00},
{0x4816, 0x52},
{0x5000, 0x73}, /* 0x7f enable DPC */
{0x5001, 0x00},
{0x5005, 0x38},
{0x501e, 0x0d},
{0x5040, 0x00},
{0x5901, 0x00},
{0x3800, 0x00},
{0x3801, 0x00},
{0x3802, 0x00},
{0x3803, 0x00},
{0x3804, 0x07},
{0x3805, 0x8f},
{0x3806, 0x04},
{0x3807, 0x47},
{0x3808, 0x07},
{0x3809, 0x8c},
{0x380a, 0x04},
{0x380b, 0x44},
{0x3810, 0x00},
{0x3811, 0x00},
{0x3812, 0x00},
{0x3813, 0x01},
{0x4003, 0x40}, /* set Black level to 0x40 */
};
static const char * const ov2740_test_pattern_menu[] = {
"Disabled",
"Color Bar",
"Top-Bottom Darker Color Bar",
"Right-Left Darker Color Bar",
"Bottom-Top Darker Color Bar",
};
static const s64 link_freq_menu_items[] = {
OV2740_LINK_FREQ_360MHZ,
OV2740_LINK_FREQ_180MHZ,
};
static const struct ov2740_link_freq_config link_freq_configs[] = {
[OV2740_LINK_FREQ_360MHZ_INDEX] = {
.reg_list = {
.num_of_regs = ARRAY_SIZE(mipi_data_rate_720mbps),
.regs = mipi_data_rate_720mbps,
}
},
[OV2740_LINK_FREQ_180MHZ_INDEX] = {
.reg_list = {
.num_of_regs = ARRAY_SIZE(mipi_data_rate_360mbps),
.regs = mipi_data_rate_360mbps,
}
},
};
static const struct ov2740_mode supported_modes_360mhz[] = {
{
.width = 1932,
.height = 1092,
.hts = 2160,
.vts_min = 1120,
.vts_def = 2186,
.vts_max = 32767,
.reg_list = {
.num_of_regs = ARRAY_SIZE(mode_1932x1092_regs_360mhz),
.regs = mode_1932x1092_regs_360mhz,
},
.link_freq_index = OV2740_LINK_FREQ_360MHZ_INDEX,
},
};
static const struct ov2740_mode supported_modes_180mhz[] = {
{
.width = 1932,
.height = 1092,
.hts = 2160,
.vts_min = 1110,
.vts_def = 1110,
.vts_max = 2047,
.reg_list = {
.num_of_regs = ARRAY_SIZE(mode_1932x1092_regs_180mhz),
.regs = mode_1932x1092_regs_180mhz,
},
.link_freq_index = OV2740_LINK_FREQ_180MHZ_INDEX,
},
};
struct ov2740 {
struct v4l2_subdev sd;
struct media_pad pad;
struct v4l2_ctrl_handler ctrl_handler;
/* V4L2 Controls */
struct v4l2_ctrl *link_freq;
struct v4l2_ctrl *pixel_rate;
struct v4l2_ctrl *vblank;
struct v4l2_ctrl *hblank;
struct v4l2_ctrl *exposure;
/* GPIOs, clocks */
struct gpio_desc *reset_gpio;
struct clk *clk;
/* Current mode */
const struct ov2740_mode *cur_mode;
/* NVM data inforamtion */
struct nvm_data *nvm;
/* Supported modes */
const struct ov2740_mode *supported_modes;
int supported_modes_count;
/* True if the device has been identified */
bool identified;
};
static inline struct ov2740 *to_ov2740(struct v4l2_subdev *subdev)
{
return container_of(subdev, struct ov2740, sd);
}
static u64 to_pixel_rate(u32 f_index)
{
u64 pixel_rate = link_freq_menu_items[f_index] * 2 * OV2740_DATA_LANES;
do_div(pixel_rate, OV2740_RGB_DEPTH);
return pixel_rate;
}
static int ov2740_read_reg(struct ov2740 *ov2740, u16 reg, u16 len, u32 *val)
{
struct i2c_client *client = v4l2_get_subdevdata(&ov2740->sd);
struct i2c_msg msgs[2];
u8 addr_buf[2];
u8 data_buf[4] = {0};
int ret;
if (len > sizeof(data_buf))
return -EINVAL;
put_unaligned_be16(reg, addr_buf);
msgs[0].addr = client->addr;
msgs[0].flags = 0;
msgs[0].len = sizeof(addr_buf);
msgs[0].buf = addr_buf;
msgs[1].addr = client->addr;
msgs[1].flags = I2C_M_RD;
msgs[1].len = len;
msgs[1].buf = &data_buf[sizeof(data_buf) - len];
ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
if (ret != ARRAY_SIZE(msgs))
return ret < 0 ? ret : -EIO;
*val = get_unaligned_be32(data_buf);
return 0;
}
static int ov2740_write_reg(struct ov2740 *ov2740, u16 reg, u16 len, u32 val)
{
struct i2c_client *client = v4l2_get_subdevdata(&ov2740->sd);
u8 buf[6];
int ret;
if (len > 4)
return -EINVAL;
put_unaligned_be16(reg, buf);
put_unaligned_be32(val << 8 * (4 - len), buf + 2);
ret = i2c_master_send(client, buf, len + 2);
if (ret != len + 2)
return ret < 0 ? ret : -EIO;
return 0;
}
static int ov2740_write_reg_list(struct ov2740 *ov2740,
const struct ov2740_reg_list *r_list)
{
struct i2c_client *client = v4l2_get_subdevdata(&ov2740->sd);
unsigned int i;
int ret;
for (i = 0; i < r_list->num_of_regs; i++) {
ret = ov2740_write_reg(ov2740, r_list->regs[i].address, 1,
r_list->regs[i].val);
if (ret) {
dev_err_ratelimited(&client->dev,
"write reg 0x%4.4x return err = %d\n",
r_list->regs[i].address, ret);
return ret;
}
}
return 0;
}
static int ov2740_identify_module(struct ov2740 *ov2740)
{
struct i2c_client *client = v4l2_get_subdevdata(&ov2740->sd);
int ret;
u32 val;
if (ov2740->identified)
return 0;
ret = ov2740_read_reg(ov2740, OV2740_REG_CHIP_ID, 3, &val);
if (ret)
return ret;
if (val != OV2740_CHIP_ID) {
dev_err(&client->dev, "chip id mismatch: %x != %x\n",
OV2740_CHIP_ID, val);
return -ENXIO;
}
ov2740->identified = true;
return 0;
}
static int ov2740_update_digital_gain(struct ov2740 *ov2740, u32 d_gain)
{
int ret;
ret = ov2740_write_reg(ov2740, OV2740_REG_GROUP_ACCESS, 1,
OV2740_GROUP_HOLD_START);
if (ret)
return ret;
ret = ov2740_write_reg(ov2740, OV2740_REG_MWB_R_GAIN, 2, d_gain);
if (ret)
return ret;
ret = ov2740_write_reg(ov2740, OV2740_REG_MWB_G_GAIN, 2, d_gain);
if (ret)
return ret;
ret = ov2740_write_reg(ov2740, OV2740_REG_MWB_B_GAIN, 2, d_gain);
if (ret)
return ret;
ret = ov2740_write_reg(ov2740, OV2740_REG_GROUP_ACCESS, 1,
OV2740_GROUP_HOLD_END);
if (ret)
return ret;
ret = ov2740_write_reg(ov2740, OV2740_REG_GROUP_ACCESS, 1,
OV2740_GROUP_HOLD_LAUNCH);
return ret;
}
static int ov2740_test_pattern(struct ov2740 *ov2740, u32 pattern)
{
if (pattern)
pattern = (pattern - 1) << OV2740_TEST_PATTERN_BAR_SHIFT |
OV2740_TEST_PATTERN_ENABLE;
return ov2740_write_reg(ov2740, OV2740_REG_TEST_PATTERN, 1, pattern);
}
static int ov2740_set_ctrl(struct v4l2_ctrl *ctrl)
{
struct ov2740 *ov2740 = container_of(ctrl->handler,
struct ov2740, ctrl_handler);
struct i2c_client *client = v4l2_get_subdevdata(&ov2740->sd);
s64 exposure_max;
int ret;
/* Propagate change of current control to all related controls */
if (ctrl->id == V4L2_CID_VBLANK) {
/* Update max exposure while meeting expected vblanking */
exposure_max = ov2740->cur_mode->height + ctrl->val -
OV2740_EXPOSURE_MAX_MARGIN;
__v4l2_ctrl_modify_range(ov2740->exposure,
ov2740->exposure->minimum,
exposure_max, ov2740->exposure->step,
exposure_max);
}
/* V4L2 controls values will be applied only when power is already up */
if (!pm_runtime_get_if_in_use(&client->dev))
return 0;
switch (ctrl->id) {
case V4L2_CID_ANALOGUE_GAIN:
ret = ov2740_write_reg(ov2740, OV2740_REG_ANALOG_GAIN, 2,
ctrl->val);
break;
case V4L2_CID_DIGITAL_GAIN:
ret = ov2740_update_digital_gain(ov2740, ctrl->val);
break;
case V4L2_CID_EXPOSURE:
/* 4 least significant bits of expsoure are fractional part */
ret = ov2740_write_reg(ov2740, OV2740_REG_EXPOSURE, 3,
ctrl->val << 4);
break;
case V4L2_CID_VBLANK:
ret = ov2740_write_reg(ov2740, OV2740_REG_VTS, 2,
ov2740->cur_mode->height + ctrl->val);
break;
case V4L2_CID_TEST_PATTERN:
ret = ov2740_test_pattern(ov2740, ctrl->val);
break;
default:
ret = -EINVAL;
break;
}
pm_runtime_put(&client->dev);
return ret;
}
static const struct v4l2_ctrl_ops ov2740_ctrl_ops = {
.s_ctrl = ov2740_set_ctrl,
};
static int ov2740_init_controls(struct ov2740 *ov2740)
{
struct v4l2_ctrl_handler *ctrl_hdlr;
const struct ov2740_mode *cur_mode;
s64 exposure_max, h_blank, pixel_rate;
u32 vblank_min, vblank_max, vblank_default;
int size;
int ret;
ctrl_hdlr = &ov2740->ctrl_handler;
ret = v4l2_ctrl_handler_init(ctrl_hdlr, 8);
if (ret)
return ret;
cur_mode = ov2740->cur_mode;
size = ARRAY_SIZE(link_freq_menu_items);
ov2740->link_freq =
v4l2_ctrl_new_int_menu(ctrl_hdlr, &ov2740_ctrl_ops,
V4L2_CID_LINK_FREQ, size - 1,
ov2740->supported_modes->link_freq_index,
link_freq_menu_items);
if (ov2740->link_freq)
ov2740->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
pixel_rate = to_pixel_rate(ov2740->supported_modes->link_freq_index);
ov2740->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &ov2740_ctrl_ops,
V4L2_CID_PIXEL_RATE, 0,
pixel_rate, 1, pixel_rate);
vblank_min = cur_mode->vts_min - cur_mode->height;
vblank_max = cur_mode->vts_max - cur_mode->height;
vblank_default = cur_mode->vts_def - cur_mode->height;
ov2740->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov2740_ctrl_ops,
V4L2_CID_VBLANK, vblank_min,
vblank_max, 1, vblank_default);
h_blank = cur_mode->hts - cur_mode->width;
ov2740->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov2740_ctrl_ops,
V4L2_CID_HBLANK, h_blank, h_blank, 1,
h_blank);
if (ov2740->hblank)
ov2740->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
v4l2_ctrl_new_std(ctrl_hdlr, &ov2740_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
OV2740_ANAL_GAIN_MIN, OV2740_ANAL_GAIN_MAX,
OV2740_ANAL_GAIN_STEP, OV2740_ANAL_GAIN_MIN);
v4l2_ctrl_new_std(ctrl_hdlr, &ov2740_ctrl_ops, V4L2_CID_DIGITAL_GAIN,
OV2740_DGTL_GAIN_MIN, OV2740_DGTL_GAIN_MAX,
OV2740_DGTL_GAIN_STEP, OV2740_DGTL_GAIN_DEFAULT);
exposure_max = cur_mode->vts_def - OV2740_EXPOSURE_MAX_MARGIN;
ov2740->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &ov2740_ctrl_ops,
V4L2_CID_EXPOSURE,
OV2740_EXPOSURE_MIN, exposure_max,
OV2740_EXPOSURE_STEP,
exposure_max);
v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &ov2740_ctrl_ops,
V4L2_CID_TEST_PATTERN,
ARRAY_SIZE(ov2740_test_pattern_menu) - 1,
0, 0, ov2740_test_pattern_menu);
media: ov2740: Fix memleak in ov2740_init_controls() There is a kmemleak when testing the media/i2c/ov2740.c with bpf mock device: unreferenced object 0xffff8881090e19e0 (size 16): comm "51-i2c-ov2740", pid 278, jiffies 4294781584 (age 23.613s) hex dump (first 16 bytes): 00 f3 7c 0b 81 88 ff ff 80 75 6a 09 81 88 ff ff ..|......uj..... backtrace: [<000000004e9fad8f>] __kmalloc_node+0x44/0x1b0 [<0000000039c802f4>] kvmalloc_node+0x34/0x180 [<000000009b8b5c63>] v4l2_ctrl_handler_init_class+0x11d/0x180 [videodev] [<0000000038644056>] ov2740_probe+0x37d/0x84f [ov2740] [<0000000092489f59>] i2c_device_probe+0x28d/0x680 [<000000001038babe>] really_probe+0x17c/0x3f0 [<0000000098c7af1c>] __driver_probe_device+0xe3/0x170 [<00000000e1b3dc24>] device_driver_attach+0x34/0x80 [<000000005a04a34d>] bind_store+0x10b/0x1a0 [<00000000ce25d4f2>] drv_attr_store+0x49/0x70 [<000000007d9f4e9a>] sysfs_kf_write+0x8c/0xb0 [<00000000be6cff0f>] kernfs_fop_write_iter+0x216/0x2e0 [<0000000031ddb40a>] vfs_write+0x658/0x810 [<0000000041beecdd>] ksys_write+0xd6/0x1b0 [<0000000023755840>] do_syscall_64+0x38/0x90 [<00000000b2cc2da2>] entry_SYSCALL_64_after_hwframe+0x63/0xcd ov2740_init_controls() won't clean all the allocated resources in fail path, which may causes the memleaks. Add v4l2_ctrl_handler_free() to prevent memleak. Fixes: 866edc895171 ("media: i2c: Add ov2740 image sensor driver") Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-12-08 15:59:37 +08:00
if (ctrl_hdlr->error) {
v4l2_ctrl_handler_free(ctrl_hdlr);
return ctrl_hdlr->error;
media: ov2740: Fix memleak in ov2740_init_controls() There is a kmemleak when testing the media/i2c/ov2740.c with bpf mock device: unreferenced object 0xffff8881090e19e0 (size 16): comm "51-i2c-ov2740", pid 278, jiffies 4294781584 (age 23.613s) hex dump (first 16 bytes): 00 f3 7c 0b 81 88 ff ff 80 75 6a 09 81 88 ff ff ..|......uj..... backtrace: [<000000004e9fad8f>] __kmalloc_node+0x44/0x1b0 [<0000000039c802f4>] kvmalloc_node+0x34/0x180 [<000000009b8b5c63>] v4l2_ctrl_handler_init_class+0x11d/0x180 [videodev] [<0000000038644056>] ov2740_probe+0x37d/0x84f [ov2740] [<0000000092489f59>] i2c_device_probe+0x28d/0x680 [<000000001038babe>] really_probe+0x17c/0x3f0 [<0000000098c7af1c>] __driver_probe_device+0xe3/0x170 [<00000000e1b3dc24>] device_driver_attach+0x34/0x80 [<000000005a04a34d>] bind_store+0x10b/0x1a0 [<00000000ce25d4f2>] drv_attr_store+0x49/0x70 [<000000007d9f4e9a>] sysfs_kf_write+0x8c/0xb0 [<00000000be6cff0f>] kernfs_fop_write_iter+0x216/0x2e0 [<0000000031ddb40a>] vfs_write+0x658/0x810 [<0000000041beecdd>] ksys_write+0xd6/0x1b0 [<0000000023755840>] do_syscall_64+0x38/0x90 [<00000000b2cc2da2>] entry_SYSCALL_64_after_hwframe+0x63/0xcd ov2740_init_controls() won't clean all the allocated resources in fail path, which may causes the memleaks. Add v4l2_ctrl_handler_free() to prevent memleak. Fixes: 866edc895171 ("media: i2c: Add ov2740 image sensor driver") Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-12-08 15:59:37 +08:00
}
ov2740->sd.ctrl_handler = ctrl_hdlr;
return 0;
}
static void ov2740_update_pad_format(const struct ov2740_mode *mode,
struct v4l2_mbus_framefmt *fmt)
{
fmt->width = mode->width;
fmt->height = mode->height;
fmt->code = MEDIA_BUS_FMT_SGRBG10_1X10;
fmt->field = V4L2_FIELD_NONE;
}
static int ov2740_load_otp_data(struct nvm_data *nvm)
{
struct device *dev = regmap_get_device(nvm->regmap);
struct ov2740 *ov2740 = to_ov2740(dev_get_drvdata(dev));
u32 isp_ctrl00 = 0;
u32 isp_ctrl01 = 0;
int ret;
if (nvm->nvm_buffer)
return 0;
nvm->nvm_buffer = kzalloc(CUSTOMER_USE_OTP_SIZE, GFP_KERNEL);
if (!nvm->nvm_buffer)
return -ENOMEM;
ret = ov2740_read_reg(ov2740, OV2740_REG_ISP_CTRL00, 1, &isp_ctrl00);
if (ret) {
dev_err(dev, "failed to read ISP CTRL00\n");
goto err;
}
ret = ov2740_read_reg(ov2740, OV2740_REG_ISP_CTRL01, 1, &isp_ctrl01);
if (ret) {
dev_err(dev, "failed to read ISP CTRL01\n");
goto err;
}
/* Clear bit 5 of ISP CTRL00 */
ret = ov2740_write_reg(ov2740, OV2740_REG_ISP_CTRL00, 1,
isp_ctrl00 & ~BIT(5));
if (ret) {
dev_err(dev, "failed to set ISP CTRL00\n");
goto err;
}
/* Clear bit 7 of ISP CTRL01 */
ret = ov2740_write_reg(ov2740, OV2740_REG_ISP_CTRL01, 1,
isp_ctrl01 & ~BIT(7));
if (ret) {
dev_err(dev, "failed to set ISP CTRL01\n");
goto err;
}
ret = ov2740_write_reg(ov2740, OV2740_REG_MODE_SELECT, 1,
OV2740_MODE_STREAMING);
if (ret) {
dev_err(dev, "failed to set streaming mode\n");
goto err;
}
/*
* Users are not allowed to access OTP-related registers and memory
* during the 20 ms period after streaming starts (0x100 = 0x01).
*/
msleep(20);
ret = regmap_bulk_read(nvm->regmap, OV2740_REG_OTP_CUSTOMER,
nvm->nvm_buffer, CUSTOMER_USE_OTP_SIZE);
if (ret) {
dev_err(dev, "failed to read OTP data, ret %d\n", ret);
goto err;
}
ret = ov2740_write_reg(ov2740, OV2740_REG_MODE_SELECT, 1,
OV2740_MODE_STANDBY);
if (ret) {
dev_err(dev, "failed to set streaming mode\n");
goto err;
}
ret = ov2740_write_reg(ov2740, OV2740_REG_ISP_CTRL01, 1, isp_ctrl01);
if (ret) {
dev_err(dev, "failed to set ISP CTRL01\n");
goto err;
}
ret = ov2740_write_reg(ov2740, OV2740_REG_ISP_CTRL00, 1, isp_ctrl00);
if (ret) {
dev_err(dev, "failed to set ISP CTRL00\n");
goto err;
}
return 0;
err:
kfree(nvm->nvm_buffer);
nvm->nvm_buffer = NULL;
return ret;
}
static int ov2740_start_streaming(struct ov2740 *ov2740)
{
struct i2c_client *client = v4l2_get_subdevdata(&ov2740->sd);
const struct ov2740_reg_list *reg_list;
int link_freq_index;
int ret;
ret = ov2740_identify_module(ov2740);
if (ret)
return ret;
if (ov2740->nvm)
ov2740_load_otp_data(ov2740->nvm);
/* Reset the sensor */
ret = ov2740_write_reg(ov2740, 0x0103, 1, 0x01);
if (ret) {
dev_err(&client->dev, "failed to reset\n");
return ret;
}
usleep_range(10000, 15000);
link_freq_index = ov2740->cur_mode->link_freq_index;
reg_list = &link_freq_configs[link_freq_index].reg_list;
ret = ov2740_write_reg_list(ov2740, reg_list);
if (ret) {
dev_err(&client->dev, "failed to set plls\n");
return ret;
}
reg_list = &ov2740->cur_mode->reg_list;
ret = ov2740_write_reg_list(ov2740, reg_list);
if (ret) {
dev_err(&client->dev, "failed to set mode\n");
return ret;
}
ret = __v4l2_ctrl_handler_setup(ov2740->sd.ctrl_handler);
if (ret)
return ret;
ret = ov2740_write_reg(ov2740, OV2740_REG_MODE_SELECT, 1,
OV2740_MODE_STREAMING);
if (ret)
dev_err(&client->dev, "failed to start streaming\n");
return ret;
}
static void ov2740_stop_streaming(struct ov2740 *ov2740)
{
struct i2c_client *client = v4l2_get_subdevdata(&ov2740->sd);
if (ov2740_write_reg(ov2740, OV2740_REG_MODE_SELECT, 1,
OV2740_MODE_STANDBY))
dev_err(&client->dev, "failed to stop streaming\n");
}
static int ov2740_set_stream(struct v4l2_subdev *sd, int enable)
{
struct ov2740 *ov2740 = to_ov2740(sd);
struct i2c_client *client = v4l2_get_subdevdata(sd);
struct v4l2_subdev_state *sd_state;
int ret = 0;
sd_state = v4l2_subdev_lock_and_get_active_state(&ov2740->sd);
if (enable) {
ret = pm_runtime_resume_and_get(&client->dev);
if (ret < 0)
goto out_unlock;
ret = ov2740_start_streaming(ov2740);
if (ret) {
enable = 0;
ov2740_stop_streaming(ov2740);
pm_runtime_put(&client->dev);
}
} else {
ov2740_stop_streaming(ov2740);
pm_runtime_put(&client->dev);
}
out_unlock:
v4l2_subdev_unlock_state(sd_state);
return ret;
}
static int ov2740_set_format(struct v4l2_subdev *sd,
media: v4l2-subdev: add subdev-wide state struct We have 'struct v4l2_subdev_pad_config' which contains configuration for a single pad used for the TRY functionality, and an array of those structs is passed to various v4l2_subdev_pad_ops. I was working on subdev internal routing between pads, and realized that there's no way to add TRY functionality for routes, which is not pad specific configuration. Adding a separate struct for try-route config wouldn't work either, as e.g. set-fmt needs to know the try-route configuration to propagate the settings. This patch adds a new struct, 'struct v4l2_subdev_state' (which at the moment only contains the v4l2_subdev_pad_config array) and the new struct is used in most of the places where v4l2_subdev_pad_config was used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config are changed to instead take v4l2_subdev_state. The changes to drivers/media/v4l2-core/v4l2-subdev.c and include/media/v4l2-subdev.h were written by hand, and all the driver changes were done with the semantic patch below. The spatch needs to be applied to a select list of directories. I used the following shell commands to apply the spatch: dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media" for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done Note that Coccinelle chokes on a few drivers (gcc extensions?). With minor changes we can make Coccinelle run fine, and these changes can be reverted after spatch. The diff for these changes is: For drivers/media/i2c/s5k5baf.c: @@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd, &s5k5baf_cis_rect, v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS), v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS), - v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT) + v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT), }; s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r); return 0; For drivers/media/platform/s3c-camif/camif-capture.c: @@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd, *mf = camif->mbus_fmt; break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* crop rectangle at camera interface input */ mf->width = camif->camif_crop.width; mf->height = camif->camif_crop.height; @@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd, } break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* Pixel format can be only changed on the sink pad. */ mf->code = camif->mbus_fmt.code; mf->width = crop->width; The semantic patch is: // <smpl> // Change function parameter @@ identifier func; identifier cfg; @@ func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...) { <... - cfg + sd_state ...> } // Change function declaration parameter @@ identifier func; identifier cfg; type T; @@ T func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...); // Change function return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...) { ... } // Change function declaration return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...); // Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it // inside a pad_state. @@ identifier func; identifier pad_cfg; @@ func(...) { ... struct v4l2_subdev_pad_config pad_cfg; + struct v4l2_subdev_state pad_state = { .pads = &pad_cfg }; <+... ( v4l2_subdev_call | sensor_call | isi_try_fse | isc_try_fse | saa_call_all ) (..., - &pad_cfg + &pad_state ,...) ...+> } // If the function uses fields from pad_config, access via state->pads @@ identifier func; identifier state; @@ func(..., struct v4l2_subdev_state *state , ...) { <... ( - state->try_fmt + state->pads->try_fmt | - state->try_crop + state->pads->try_crop | - state->try_compose + state->pads->try_compose ) ...> } // If the function accesses the filehandle, use fh->state instead @@ struct v4l2_subdev_fh *fh; @@ - fh->pad + fh->state @@ struct v4l2_subdev_fh fh; @@ - fh.pad + fh.state // Start of vsp1 specific @@ @@ struct vsp1_entity { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... }; @@ symbol entity; @@ vsp1_entity_init(...) { ... entity->config = - v4l2_subdev_alloc_pad_config + v4l2_subdev_alloc_state (&entity->subdev); ... } @@ symbol entity; @@ vsp1_entity_destroy(...) { ... - v4l2_subdev_free_pad_config + v4l2_subdev_free_state (entity->config); ... } @exists@ identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)"; symbol config; @@ func(...) { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... } // End of vsp1 specific // Start of rcar specific @@ identifier sd; identifier pad_cfg; @@ rvin_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } // End of rcar specific // Start of rockchip specific @@ identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)"; symbol rsz; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = rsz->pad_cfg }; ... - rsz->pad_cfg + &state ... } @@ identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)"; symbol isp; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = isp->pad_cfg }; ... - isp->pad_cfg + &state ... } @@ symbol rkisp1; symbol isp; symbol pad_cfg; @@ rkisp1_isp_register(...) { + struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg }; ... - rkisp1->isp.pad_cfg + &state ... } // End of rockchip specific // Start of tegra-video specific @@ identifier sd; identifier pad_cfg; @@ __tegra_channel_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } @@ identifier sd_state; @@ __tegra_channel_try_format(...) { ... struct v4l2_subdev_state *sd_state; <... - sd_state->try_crop + sd_state->pads->try_crop ...> } // End of tegra-video specific // </smpl> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-06-10 22:55:58 +08:00
struct v4l2_subdev_state *sd_state,
struct v4l2_subdev_format *fmt)
{
struct ov2740 *ov2740 = to_ov2740(sd);
const struct ov2740_mode *mode;
s32 vblank_def, h_blank;
mode = v4l2_find_nearest_size(ov2740->supported_modes,
ov2740->supported_modes_count,
width, height,
fmt->format.width, fmt->format.height);
ov2740_update_pad_format(mode, &fmt->format);
media: v4l: subdev: Switch to stream-aware state functions Switch all drivers accessing sub-device state to use the stream-aware functions. We will soon remove the old ones. This patch has been generated using the following Coccinelle script: ---------8<------------ @@ expression E1, E2, E3; @@ - v4l2_subdev_get_pad_format(E1, E2, E3) + v4l2_subdev_state_get_format(E2, E3) @@ expression E1, E2, E3; @@ - v4l2_subdev_get_pad_crop(E1, E2, E3) + v4l2_subdev_state_get_crop(E2, E3) @@ expression E1, E2, E3; @@ - v4l2_subdev_get_pad_compose(E1, E2, E3) + v4l2_subdev_state_get_compose(E2, E3) @@ expression E1, E2, E3; @@ - v4l2_subdev_get_try_format(E1, E2, E3) + v4l2_subdev_state_get_format(E2, E3) @@ expression E1, E2, E3; @@ - v4l2_subdev_get_try_crop(E1, E2, E3) + v4l2_subdev_state_get_crop(E2, E3) @@ expression E1, E2, E3; @@ - v4l2_subdev_get_try_compose(E1, E2, E3) + v4l2_subdev_state_get_compose(E2, E3) ---------8<------------ Additionally drivers/media/i2c/s5k5baf.c and drivers/media/platform/samsung/s3c-camif/camif-capture.c have been manually changed as Coccinelle didn't. Further local variables have been removed as they became unused as a result of the other changes. Also Coccinelle introduced indentation by space in files drivers/media/i2c/st-mipid02.c and drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c. This has been also corrected. The diff from Coccinelle-generated changes are: > diff --git b/drivers/media/i2c/imx319.c a/drivers/media/i2c/imx319.c > index e549692ff478..420984382173 100644 > --- b/drivers/media/i2c/imx319.c > +++ a/drivers/media/i2c/imx319.c > @@ -2001,7 +2001,6 @@ static int imx319_do_get_pad_format(struct imx319 *imx319, > struct v4l2_subdev_format *fmt) > { > struct v4l2_mbus_framefmt *framefmt; > - struct v4l2_subdev *sd = &imx319->sd; > > if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { > framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad); > diff --git b/drivers/media/i2c/imx355.c a/drivers/media/i2c/imx355.c > index 96bdde685d65..e1b1d2fc79dd 100644 > --- b/drivers/media/i2c/imx355.c > +++ a/drivers/media/i2c/imx355.c > @@ -1299,7 +1299,6 @@ static int imx355_do_get_pad_format(struct imx355 *imx355, > struct v4l2_subdev_format *fmt) > { > struct v4l2_mbus_framefmt *framefmt; > - struct v4l2_subdev *sd = &imx355->sd; > > if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { > framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad); > diff --git b/drivers/media/i2c/ov08x40.c a/drivers/media/i2c/ov08x40.c > index ca799bbcfdb7..abbb0b774d43 100644 > --- b/drivers/media/i2c/ov08x40.c > +++ a/drivers/media/i2c/ov08x40.c > @@ -2774,7 +2774,6 @@ static int ov08x40_do_get_pad_format(struct ov08x40 *ov08x, > struct v4l2_subdev_format *fmt) > { > struct v4l2_mbus_framefmt *framefmt; > - struct v4l2_subdev *sd = &ov08x->sd; > > if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { > framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad); > diff --git b/drivers/media/i2c/ov13858.c a/drivers/media/i2c/ov13858.c > index 7816d9787c61..09387e335d80 100644 > --- b/drivers/media/i2c/ov13858.c > +++ a/drivers/media/i2c/ov13858.c > @@ -1316,7 +1316,6 @@ static int ov13858_do_get_pad_format(struct ov13858 *ov13858, > struct v4l2_subdev_format *fmt) > { > struct v4l2_mbus_framefmt *framefmt; > - struct v4l2_subdev *sd = &ov13858->sd; > > if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { > framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad); > diff --git b/drivers/media/i2c/ov13b10.c a/drivers/media/i2c/ov13b10.c > index 268cd4b03f9c..c06411d5ee2b 100644 > --- b/drivers/media/i2c/ov13b10.c > +++ a/drivers/media/i2c/ov13b10.c > @@ -1001,7 +1001,6 @@ static int ov13b10_do_get_pad_format(struct ov13b10 *ov13b, > struct v4l2_subdev_format *fmt) > { > struct v4l2_mbus_framefmt *framefmt; > - struct v4l2_subdev *sd = &ov13b->sd; > > if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { > framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad); > diff --git b/drivers/media/i2c/s5c73m3/s5c73m3-core.c a/drivers/media/i2c/s5c73m3/s5c73m3-core.c > index 47605e36bc60..8f9b5713daf7 100644 > --- b/drivers/media/i2c/s5c73m3/s5c73m3-core.c > +++ a/drivers/media/i2c/s5c73m3/s5c73m3-core.c > @@ -819,7 +819,6 @@ static void s5c73m3_oif_try_format(struct s5c73m3 *state, > struct v4l2_subdev_format *fmt, > const struct s5c73m3_frame_size **fs) > { > - struct v4l2_subdev *sd = &state->sensor_sd; > u32 code; > > switch (fmt->pad) { > diff --git a/drivers/media/i2c/s5k5baf.c b/drivers/media/i2c/s5k5baf.c > index 67da2045f543..03ccfb0e1e11 100644 > --- a/drivers/media/i2c/s5k5baf.c > +++ b/drivers/media/i2c/s5k5baf.c > @@ -1472,14 +1472,11 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd, > > if (sel->which == V4L2_SUBDEV_FORMAT_TRY) { > rects = (struct v4l2_rect * []) { > - &s5k5baf_cis_rect, > - v4l2_subdev_get_try_crop(sd, sd_state, > - PAD_CIS), > - v4l2_subdev_get_try_compose(sd, sd_state, > - PAD_CIS), > - v4l2_subdev_get_try_crop(sd, sd_state, > - PAD_OUT) > - }; > + &s5k5baf_cis_rect, > + v4l2_subdev_state_get_crop(sd_state, PAD_CIS), > + v4l2_subdev_state_get_compose(sd_state, PAD_CIS), > + v4l2_subdev_state_get_crop(sd_state, PAD_OUT) > + }; > s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r); > return 0; > } > diff --git b/drivers/media/platform/samsung/s3c-camif/camif-capture.c a/drivers/media/platform/samsung/s3c-camif/camif-capture.c > index 295e083f38e8..be58260ea67e 100644 > --- b/drivers/media/platform/samsung/s3c-camif/camif-capture.c > +++ a/drivers/media/platform/samsung/s3c-camif/camif-capture.c > @@ -1216,7 +1216,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd, > struct v4l2_mbus_framefmt *mf = &fmt->format; > > if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { > - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad); > + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad); > fmt->format = *mf; > return 0; > } > @@ -1305,7 +1305,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd, > __camif_subdev_try_format(camif, mf, fmt->pad); > > if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { > - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad); > + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad); > *mf = fmt->format; > mutex_unlock(&camif->lock); > return 0; > diff --git b/drivers/media/platform/ti/cal/cal-camerarx.c a/drivers/media/platform/ti/cal/cal-camerarx.c > index cea454ed9c20..61433744c6c4 100644 > --- b/drivers/media/platform/ti/cal/cal-camerarx.c > +++ a/drivers/media/platform/ti/cal/cal-camerarx.c > @@ -621,8 +621,6 @@ static int cal_camerarx_sd_enum_mbus_code(struct v4l2_subdev *sd, > struct v4l2_subdev_state *state, > struct v4l2_subdev_mbus_code_enum *code) > { > - struct cal_camerarx *phy = to_cal_camerarx(sd); > - > /* No transcoding, source and sink codes must match. */ > if (cal_rx_pad_is_source(code->pad)) { > struct v4l2_mbus_framefmt *fmt; > diff --git b/drivers/staging/media/imx/imx-ic-prp.c a/drivers/staging/media/imx/imx-ic-prp.c > index dd558fac6477..61d69f19657e 100644 > --- b/drivers/staging/media/imx/imx-ic-prp.c > +++ a/drivers/staging/media/imx/imx-ic-prp.c > @@ -82,8 +82,6 @@ static struct v4l2_mbus_framefmt * > __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state, > unsigned int pad, enum v4l2_subdev_format_whence which) > { > - struct imx_ic_priv *ic_priv = priv->ic_priv; > - > if (which == V4L2_SUBDEV_FORMAT_TRY) > return v4l2_subdev_state_get_format(sd_state, pad); > else > diff --git b/drivers/staging/media/imx/imx-ic-prpencvf.c a/drivers/staging/media/imx/imx-ic-prpencvf.c > index 02db7dbb884b..ec73c901079e 100644 > --- b/drivers/staging/media/imx/imx-ic-prpencvf.c > +++ a/drivers/staging/media/imx/imx-ic-prpencvf.c > @@ -790,8 +790,6 @@ static struct v4l2_mbus_framefmt * > __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state, > unsigned int pad, enum v4l2_subdev_format_whence which) > { > - struct imx_ic_priv *ic_priv = priv->ic_priv; > - > if (which == V4L2_SUBDEV_FORMAT_TRY) > return v4l2_subdev_state_get_format(sd_state, pad); > else > diff --git a/drivers/media/i2c/st-mipid02.c b/drivers/media/i2c/st-mipid02.c > index 9c9361354c00..b08a249b5fdd 100644 > --- a/drivers/media/i2c/st-mipid02.c > +++ b/drivers/media/i2c/st-mipid02.c > @@ -751,7 +751,7 @@ static void mipid02_set_fmt_source(struct v4l2_subdev *sd, > format->format = bridge->fmt; > else > format->format = *v4l2_subdev_state_get_format(sd_state, > - MIPID02_SINK_0); > + MIPID02_SINK_0); > > /* but code may need to be converted */ > format->format.code = serial_to_parallel_code(format->format.code); > diff --git a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c > index 117912d3bfbd..96353648c032 100644 > --- a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c > +++ b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c > @@ -319,7 +319,7 @@ static void rkisp1_isp_start(struct rkisp1_isp *isp, > rkisp1_write(rkisp1, RKISP1_CIF_ISP_CTRL, val); > > src_fmt = v4l2_subdev_state_get_format(sd_state, > - RKISP1_ISP_PAD_SOURCE_VIDEO); > + RKISP1_ISP_PAD_SOURCE_VIDEO); > src_info = rkisp1_mbus_info_get_by_code(src_fmt->code); > > if (src_info->pixel_enc != V4L2_PIXEL_ENC_BAYER) > @@ -475,9 +475,9 @@ static void rkisp1_isp_set_src_fmt(struct rkisp1_isp *isp, > sink_fmt = v4l2_subdev_state_get_format(sd_state, > RKISP1_ISP_PAD_SINK_VIDEO); > src_fmt = v4l2_subdev_state_get_format(sd_state, > - RKISP1_ISP_PAD_SOURCE_VIDEO); > + RKISP1_ISP_PAD_SOURCE_VIDEO); > src_crop = v4l2_subdev_state_get_crop(sd_state, > - RKISP1_ISP_PAD_SOURCE_VIDEO); > + RKISP1_ISP_PAD_SOURCE_VIDEO); > > /* > * Media bus code. The ISP can operate in pass-through mode (Bayer in, Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2023-10-13 15:37:10 +08:00
*v4l2_subdev_state_get_format(sd_state, fmt->pad) = fmt->format;
if (fmt->which == V4L2_SUBDEV_FORMAT_TRY)
return 0;
ov2740->cur_mode = mode;
__v4l2_ctrl_s_ctrl(ov2740->link_freq, mode->link_freq_index);
__v4l2_ctrl_s_ctrl_int64(ov2740->pixel_rate,
to_pixel_rate(mode->link_freq_index));
/* Update limits and set FPS to default */
vblank_def = mode->vts_def - mode->height;
__v4l2_ctrl_modify_range(ov2740->vblank,
mode->vts_min - mode->height,
mode->vts_max - mode->height, 1, vblank_def);
__v4l2_ctrl_s_ctrl(ov2740->vblank, vblank_def);
h_blank = mode->hts - mode->width;
__v4l2_ctrl_modify_range(ov2740->hblank, h_blank, h_blank, 1, h_blank);
return 0;
}
static int ov2740_enum_mbus_code(struct v4l2_subdev *sd,
media: v4l2-subdev: add subdev-wide state struct We have 'struct v4l2_subdev_pad_config' which contains configuration for a single pad used for the TRY functionality, and an array of those structs is passed to various v4l2_subdev_pad_ops. I was working on subdev internal routing between pads, and realized that there's no way to add TRY functionality for routes, which is not pad specific configuration. Adding a separate struct for try-route config wouldn't work either, as e.g. set-fmt needs to know the try-route configuration to propagate the settings. This patch adds a new struct, 'struct v4l2_subdev_state' (which at the moment only contains the v4l2_subdev_pad_config array) and the new struct is used in most of the places where v4l2_subdev_pad_config was used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config are changed to instead take v4l2_subdev_state. The changes to drivers/media/v4l2-core/v4l2-subdev.c and include/media/v4l2-subdev.h were written by hand, and all the driver changes were done with the semantic patch below. The spatch needs to be applied to a select list of directories. I used the following shell commands to apply the spatch: dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media" for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done Note that Coccinelle chokes on a few drivers (gcc extensions?). With minor changes we can make Coccinelle run fine, and these changes can be reverted after spatch. The diff for these changes is: For drivers/media/i2c/s5k5baf.c: @@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd, &s5k5baf_cis_rect, v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS), v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS), - v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT) + v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT), }; s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r); return 0; For drivers/media/platform/s3c-camif/camif-capture.c: @@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd, *mf = camif->mbus_fmt; break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* crop rectangle at camera interface input */ mf->width = camif->camif_crop.width; mf->height = camif->camif_crop.height; @@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd, } break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* Pixel format can be only changed on the sink pad. */ mf->code = camif->mbus_fmt.code; mf->width = crop->width; The semantic patch is: // <smpl> // Change function parameter @@ identifier func; identifier cfg; @@ func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...) { <... - cfg + sd_state ...> } // Change function declaration parameter @@ identifier func; identifier cfg; type T; @@ T func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...); // Change function return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...) { ... } // Change function declaration return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...); // Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it // inside a pad_state. @@ identifier func; identifier pad_cfg; @@ func(...) { ... struct v4l2_subdev_pad_config pad_cfg; + struct v4l2_subdev_state pad_state = { .pads = &pad_cfg }; <+... ( v4l2_subdev_call | sensor_call | isi_try_fse | isc_try_fse | saa_call_all ) (..., - &pad_cfg + &pad_state ,...) ...+> } // If the function uses fields from pad_config, access via state->pads @@ identifier func; identifier state; @@ func(..., struct v4l2_subdev_state *state , ...) { <... ( - state->try_fmt + state->pads->try_fmt | - state->try_crop + state->pads->try_crop | - state->try_compose + state->pads->try_compose ) ...> } // If the function accesses the filehandle, use fh->state instead @@ struct v4l2_subdev_fh *fh; @@ - fh->pad + fh->state @@ struct v4l2_subdev_fh fh; @@ - fh.pad + fh.state // Start of vsp1 specific @@ @@ struct vsp1_entity { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... }; @@ symbol entity; @@ vsp1_entity_init(...) { ... entity->config = - v4l2_subdev_alloc_pad_config + v4l2_subdev_alloc_state (&entity->subdev); ... } @@ symbol entity; @@ vsp1_entity_destroy(...) { ... - v4l2_subdev_free_pad_config + v4l2_subdev_free_state (entity->config); ... } @exists@ identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)"; symbol config; @@ func(...) { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... } // End of vsp1 specific // Start of rcar specific @@ identifier sd; identifier pad_cfg; @@ rvin_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } // End of rcar specific // Start of rockchip specific @@ identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)"; symbol rsz; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = rsz->pad_cfg }; ... - rsz->pad_cfg + &state ... } @@ identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)"; symbol isp; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = isp->pad_cfg }; ... - isp->pad_cfg + &state ... } @@ symbol rkisp1; symbol isp; symbol pad_cfg; @@ rkisp1_isp_register(...) { + struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg }; ... - rkisp1->isp.pad_cfg + &state ... } // End of rockchip specific // Start of tegra-video specific @@ identifier sd; identifier pad_cfg; @@ __tegra_channel_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } @@ identifier sd_state; @@ __tegra_channel_try_format(...) { ... struct v4l2_subdev_state *sd_state; <... - sd_state->try_crop + sd_state->pads->try_crop ...> } // End of tegra-video specific // </smpl> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-06-10 22:55:58 +08:00
struct v4l2_subdev_state *sd_state,
struct v4l2_subdev_mbus_code_enum *code)
{
if (code->index > 0)
return -EINVAL;
code->code = MEDIA_BUS_FMT_SGRBG10_1X10;
return 0;
}
static int ov2740_enum_frame_size(struct v4l2_subdev *sd,
media: v4l2-subdev: add subdev-wide state struct We have 'struct v4l2_subdev_pad_config' which contains configuration for a single pad used for the TRY functionality, and an array of those structs is passed to various v4l2_subdev_pad_ops. I was working on subdev internal routing between pads, and realized that there's no way to add TRY functionality for routes, which is not pad specific configuration. Adding a separate struct for try-route config wouldn't work either, as e.g. set-fmt needs to know the try-route configuration to propagate the settings. This patch adds a new struct, 'struct v4l2_subdev_state' (which at the moment only contains the v4l2_subdev_pad_config array) and the new struct is used in most of the places where v4l2_subdev_pad_config was used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config are changed to instead take v4l2_subdev_state. The changes to drivers/media/v4l2-core/v4l2-subdev.c and include/media/v4l2-subdev.h were written by hand, and all the driver changes were done with the semantic patch below. The spatch needs to be applied to a select list of directories. I used the following shell commands to apply the spatch: dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media" for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done Note that Coccinelle chokes on a few drivers (gcc extensions?). With minor changes we can make Coccinelle run fine, and these changes can be reverted after spatch. The diff for these changes is: For drivers/media/i2c/s5k5baf.c: @@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd, &s5k5baf_cis_rect, v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS), v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS), - v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT) + v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT), }; s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r); return 0; For drivers/media/platform/s3c-camif/camif-capture.c: @@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd, *mf = camif->mbus_fmt; break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* crop rectangle at camera interface input */ mf->width = camif->camif_crop.width; mf->height = camif->camif_crop.height; @@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd, } break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* Pixel format can be only changed on the sink pad. */ mf->code = camif->mbus_fmt.code; mf->width = crop->width; The semantic patch is: // <smpl> // Change function parameter @@ identifier func; identifier cfg; @@ func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...) { <... - cfg + sd_state ...> } // Change function declaration parameter @@ identifier func; identifier cfg; type T; @@ T func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...); // Change function return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...) { ... } // Change function declaration return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...); // Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it // inside a pad_state. @@ identifier func; identifier pad_cfg; @@ func(...) { ... struct v4l2_subdev_pad_config pad_cfg; + struct v4l2_subdev_state pad_state = { .pads = &pad_cfg }; <+... ( v4l2_subdev_call | sensor_call | isi_try_fse | isc_try_fse | saa_call_all ) (..., - &pad_cfg + &pad_state ,...) ...+> } // If the function uses fields from pad_config, access via state->pads @@ identifier func; identifier state; @@ func(..., struct v4l2_subdev_state *state , ...) { <... ( - state->try_fmt + state->pads->try_fmt | - state->try_crop + state->pads->try_crop | - state->try_compose + state->pads->try_compose ) ...> } // If the function accesses the filehandle, use fh->state instead @@ struct v4l2_subdev_fh *fh; @@ - fh->pad + fh->state @@ struct v4l2_subdev_fh fh; @@ - fh.pad + fh.state // Start of vsp1 specific @@ @@ struct vsp1_entity { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... }; @@ symbol entity; @@ vsp1_entity_init(...) { ... entity->config = - v4l2_subdev_alloc_pad_config + v4l2_subdev_alloc_state (&entity->subdev); ... } @@ symbol entity; @@ vsp1_entity_destroy(...) { ... - v4l2_subdev_free_pad_config + v4l2_subdev_free_state (entity->config); ... } @exists@ identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)"; symbol config; @@ func(...) { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... } // End of vsp1 specific // Start of rcar specific @@ identifier sd; identifier pad_cfg; @@ rvin_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } // End of rcar specific // Start of rockchip specific @@ identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)"; symbol rsz; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = rsz->pad_cfg }; ... - rsz->pad_cfg + &state ... } @@ identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)"; symbol isp; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = isp->pad_cfg }; ... - isp->pad_cfg + &state ... } @@ symbol rkisp1; symbol isp; symbol pad_cfg; @@ rkisp1_isp_register(...) { + struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg }; ... - rkisp1->isp.pad_cfg + &state ... } // End of rockchip specific // Start of tegra-video specific @@ identifier sd; identifier pad_cfg; @@ __tegra_channel_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } @@ identifier sd_state; @@ __tegra_channel_try_format(...) { ... struct v4l2_subdev_state *sd_state; <... - sd_state->try_crop + sd_state->pads->try_crop ...> } // End of tegra-video specific // </smpl> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-06-10 22:55:58 +08:00
struct v4l2_subdev_state *sd_state,
struct v4l2_subdev_frame_size_enum *fse)
{
struct ov2740 *ov2740 = to_ov2740(sd);
const struct ov2740_mode *supported_modes = ov2740->supported_modes;
if (fse->index >= ov2740->supported_modes_count)
return -EINVAL;
if (fse->code != MEDIA_BUS_FMT_SGRBG10_1X10)
return -EINVAL;
fse->min_width = supported_modes[fse->index].width;
fse->max_width = fse->min_width;
fse->min_height = supported_modes[fse->index].height;
fse->max_height = fse->min_height;
return 0;
}
static int ov2740_init_state(struct v4l2_subdev *sd,
struct v4l2_subdev_state *sd_state)
{
struct ov2740 *ov2740 = to_ov2740(sd);
ov2740_update_pad_format(&ov2740->supported_modes[0],
v4l2_subdev_state_get_format(sd_state, 0));
return 0;
}
static const struct v4l2_subdev_video_ops ov2740_video_ops = {
.s_stream = ov2740_set_stream,
};
static const struct v4l2_subdev_pad_ops ov2740_pad_ops = {
.get_fmt = v4l2_subdev_get_fmt,
.set_fmt = ov2740_set_format,
.enum_mbus_code = ov2740_enum_mbus_code,
.enum_frame_size = ov2740_enum_frame_size,
};
static const struct v4l2_subdev_ops ov2740_subdev_ops = {
.video = &ov2740_video_ops,
.pad = &ov2740_pad_ops,
};
static const struct v4l2_subdev_internal_ops ov2740_internal_ops = {
.init_state = ov2740_init_state,
};
static const struct media_entity_operations ov2740_subdev_entity_ops = {
.link_validate = v4l2_subdev_link_validate,
};
static int ov2740_check_hwcfg(struct device *dev)
{
struct v4l2_subdev *sd = dev_get_drvdata(dev);
struct ov2740 *ov2740 = to_ov2740(sd);
struct fwnode_handle *ep;
struct fwnode_handle *fwnode = dev_fwnode(dev);
struct v4l2_fwnode_endpoint bus_cfg = {
.bus_type = V4L2_MBUS_CSI2_DPHY
};
u32 mclk;
int ret;
unsigned int i, j;
/*
* Sometimes the fwnode graph is initialized by the bridge driver,
* wait for this.
*/
ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
if (!ep)
return -EPROBE_DEFER;
ret = fwnode_property_read_u32(fwnode, "clock-frequency", &mclk);
if (ret) {
fwnode_handle_put(ep);
return dev_err_probe(dev, ret,
"reading clock-frequency property\n");
}
if (mclk != OV2740_MCLK) {
fwnode_handle_put(ep);
return dev_err_probe(dev, -EINVAL,
"external clock %d is not supported\n",
mclk);
}
ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
fwnode_handle_put(ep);
if (ret)
return dev_err_probe(dev, ret, "parsing endpoint failed\n");
if (bus_cfg.bus.mipi_csi2.num_data_lanes != OV2740_DATA_LANES) {
ret = dev_err_probe(dev, -EINVAL,
"number of CSI2 data lanes %d is not supported\n",
bus_cfg.bus.mipi_csi2.num_data_lanes);
goto check_hwcfg_error;
}
if (!bus_cfg.nr_of_link_frequencies) {
ret = dev_err_probe(dev, -EINVAL, "no link frequencies defined\n");
goto check_hwcfg_error;
}
for (i = 0; i < ARRAY_SIZE(link_freq_menu_items); i++) {
for (j = 0; j < bus_cfg.nr_of_link_frequencies; j++) {
if (link_freq_menu_items[i] ==
bus_cfg.link_frequencies[j])
break;
}
if (j == bus_cfg.nr_of_link_frequencies)
continue;
switch (i) {
case OV2740_LINK_FREQ_360MHZ_INDEX:
ov2740->supported_modes = supported_modes_360mhz;
ov2740->supported_modes_count =
ARRAY_SIZE(supported_modes_360mhz);
break;
case OV2740_LINK_FREQ_180MHZ_INDEX:
ov2740->supported_modes = supported_modes_180mhz;
ov2740->supported_modes_count =
ARRAY_SIZE(supported_modes_180mhz);
break;
}
break; /* Prefer modes from first available link-freq */
}
if (!ov2740->supported_modes)
ret = dev_err_probe(dev, -EINVAL,
"no supported link frequencies\n");
check_hwcfg_error:
v4l2_fwnode_endpoint_free(&bus_cfg);
return ret;
}
i2c: Make remove callback return void The value returned by an i2c driver's remove function is mostly ignored. (Only an error message is printed if the value is non-zero that the error is ignored.) So change the prototype of the remove function to return no value. This way driver authors are not tempted to assume that passing an error to the upper layer is a good idea. All drivers are adapted accordingly. There is no intended change of behaviour, all callbacks were prepared to return 0 before. Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com> Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au> Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Crt Mori <cmo@melexis.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013 Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/* Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5 Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860 Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power Acked-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2022-08-15 16:02:30 +08:00
static void ov2740_remove(struct i2c_client *client)
{
struct v4l2_subdev *sd = i2c_get_clientdata(client);
v4l2_async_unregister_subdev(sd);
media_entity_cleanup(&sd->entity);
v4l2_subdev_cleanup(sd);
v4l2_ctrl_handler_free(sd->ctrl_handler);
pm_runtime_disable(&client->dev);
}
static int ov2740_nvmem_read(void *priv, unsigned int off, void *val,
size_t count)
{
struct nvm_data *nvm = priv;
struct device *dev = regmap_get_device(nvm->regmap);
struct ov2740 *ov2740 = to_ov2740(dev_get_drvdata(dev));
struct v4l2_subdev_state *sd_state;
int ret = 0;
/* Serialise sensor access */
sd_state = v4l2_subdev_lock_and_get_active_state(&ov2740->sd);
if (nvm->nvm_buffer) {
memcpy(val, nvm->nvm_buffer + off, count);
goto exit;
}
ret = pm_runtime_resume_and_get(dev);
if (ret < 0) {
goto exit;
}
ret = ov2740_load_otp_data(nvm);
if (!ret)
memcpy(val, nvm->nvm_buffer + off, count);
pm_runtime_put(dev);
exit:
v4l2_subdev_unlock_state(sd_state);
return ret;
}
static int ov2740_register_nvmem(struct i2c_client *client,
struct ov2740 *ov2740)
{
struct nvm_data *nvm;
struct regmap_config regmap_config = { };
struct nvmem_config nvmem_config = { };
struct regmap *regmap;
struct device *dev = &client->dev;
nvm = devm_kzalloc(dev, sizeof(*nvm), GFP_KERNEL);
if (!nvm)
return -ENOMEM;
regmap_config.val_bits = 8;
regmap_config.reg_bits = 16;
regmap_config.disable_locking = true;
regmap = devm_regmap_init_i2c(client, &regmap_config);
if (IS_ERR(regmap))
return PTR_ERR(regmap);
nvm->regmap = regmap;
nvmem_config.name = dev_name(dev);
nvmem_config.dev = dev;
nvmem_config.read_only = true;
nvmem_config.root_only = true;
nvmem_config.owner = THIS_MODULE;
nvmem_config.compat = true;
nvmem_config.base_dev = dev;
nvmem_config.reg_read = ov2740_nvmem_read;
nvmem_config.reg_write = NULL;
nvmem_config.priv = nvm;
nvmem_config.stride = 1;
nvmem_config.word_size = 1;
nvmem_config.size = CUSTOMER_USE_OTP_SIZE;
nvm->nvmem = devm_nvmem_register(dev, &nvmem_config);
if (IS_ERR(nvm->nvmem))
return PTR_ERR(nvm->nvmem);
ov2740->nvm = nvm;
return 0;
}
static int ov2740_suspend(struct device *dev)
{
struct v4l2_subdev *sd = dev_get_drvdata(dev);
struct ov2740 *ov2740 = to_ov2740(sd);
gpiod_set_value_cansleep(ov2740->reset_gpio, 1);
clk_disable_unprepare(ov2740->clk);
return 0;
}
static int ov2740_resume(struct device *dev)
{
struct v4l2_subdev *sd = dev_get_drvdata(dev);
struct ov2740 *ov2740 = to_ov2740(sd);
int ret;
ret = clk_prepare_enable(ov2740->clk);
if (ret)
return ret;
gpiod_set_value_cansleep(ov2740->reset_gpio, 0);
msleep(20);
return 0;
}
static int ov2740_probe(struct i2c_client *client)
{
struct device *dev = &client->dev;
struct ov2740 *ov2740;
bool full_power;
int ret;
ov2740 = devm_kzalloc(&client->dev, sizeof(*ov2740), GFP_KERNEL);
if (!ov2740)
return -ENOMEM;
v4l2_i2c_subdev_init(&ov2740->sd, client, &ov2740_subdev_ops);
ov2740->sd.internal_ops = &ov2740_internal_ops;
ret = ov2740_check_hwcfg(dev);
if (ret)
return dev_err_probe(dev, ret, "failed to check HW configuration\n");
ov2740->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
if (IS_ERR(ov2740->reset_gpio)) {
return dev_err_probe(dev, PTR_ERR(ov2740->reset_gpio),
"failed to get reset GPIO\n");
} else if (ov2740->reset_gpio) {
/*
* Ensure reset is asserted for at least 20 ms before
* ov2740_resume() deasserts it.
*/
msleep(20);
}
ov2740->clk = devm_clk_get_optional(dev, "clk");
if (IS_ERR(ov2740->clk))
return dev_err_probe(dev, PTR_ERR(ov2740->clk),
"failed to get clock\n");
full_power = acpi_dev_state_d0(&client->dev);
if (full_power) {
/* ACPI does not always clear the reset GPIO / enable the clock */
ret = ov2740_resume(dev);
if (ret)
return dev_err_probe(dev, ret, "failed to power on sensor\n");
ret = ov2740_identify_module(ov2740);
if (ret) {
dev_err_probe(dev, ret, "failed to find sensor\n");
goto probe_error_power_off;
}
}
ov2740->cur_mode = &ov2740->supported_modes[0];
ret = ov2740_init_controls(ov2740);
if (ret) {
dev_err_probe(dev, ret, "failed to init controls\n");
goto probe_error_v4l2_ctrl_handler_free;
}
ov2740->sd.state_lock = ov2740->ctrl_handler.lock;
ov2740->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
ov2740->sd.entity.ops = &ov2740_subdev_entity_ops;
ov2740->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
ov2740->pad.flags = MEDIA_PAD_FL_SOURCE;
ret = media_entity_pads_init(&ov2740->sd.entity, 1, &ov2740->pad);
if (ret) {
dev_err_probe(dev, ret, "failed to init entity pads\n");
goto probe_error_v4l2_ctrl_handler_free;
}
ret = v4l2_subdev_init_finalize(&ov2740->sd);
if (ret)
goto probe_error_media_entity_cleanup;
/* Set the device's state to active if it's in D0 state. */
if (full_power)
pm_runtime_set_active(&client->dev);
pm_runtime_enable(&client->dev);
pm_runtime_idle(&client->dev);
ret = v4l2_async_register_subdev_sensor(&ov2740->sd);
if (ret < 0) {
dev_err_probe(dev, ret, "failed to register V4L2 subdev\n");
goto probe_error_v4l2_subdev_cleanup;
}
ret = ov2740_register_nvmem(client, ov2740);
if (ret)
dev_warn(&client->dev, "register nvmem failed, ret %d\n", ret);
return 0;
probe_error_v4l2_subdev_cleanup:
v4l2_subdev_cleanup(&ov2740->sd);
probe_error_media_entity_cleanup:
media_entity_cleanup(&ov2740->sd.entity);
pm_runtime_disable(&client->dev);
pm_runtime_set_suspended(&client->dev);
probe_error_v4l2_ctrl_handler_free:
v4l2_ctrl_handler_free(ov2740->sd.ctrl_handler);
probe_error_power_off:
if (full_power)
ov2740_suspend(dev);
return ret;
}
static DEFINE_RUNTIME_DEV_PM_OPS(ov2740_pm_ops, ov2740_suspend, ov2740_resume,
NULL);
static const struct acpi_device_id ov2740_acpi_ids[] = {
{"INT3474"},
{}
};
MODULE_DEVICE_TABLE(acpi, ov2740_acpi_ids);
static struct i2c_driver ov2740_i2c_driver = {
.driver = {
.name = "ov2740",
.acpi_match_table = ov2740_acpi_ids,
.pm = pm_sleep_ptr(&ov2740_pm_ops),
},
.probe = ov2740_probe,
.remove = ov2740_remove,
.flags = I2C_DRV_ACPI_WAIVE_D0_PROBE,
};
module_i2c_driver(ov2740_i2c_driver);
MODULE_AUTHOR("Qiu, Tianshu <tian.shu.qiu@intel.com>");
MODULE_AUTHOR("Shawn Tu");
MODULE_AUTHOR("Bingbu Cao <bingbu.cao@intel.com>");
MODULE_DESCRIPTION("OmniVision OV2740 sensor driver");
MODULE_LICENSE("GPL v2");