0
0
mirror of https://mirrors.bfsu.edu.cn/git/linux.git synced 2024-12-16 15:34:48 +08:00
linux/drivers/spi/spi-geni-qcom.c

1269 lines
34 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0
// Copyright (c) 2017-2018, The Linux foundation. All rights reserved.
#include <linux/clk.h>
#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
#include <linux/dma/qcom-gpi-dma.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/log2.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/pm_opp.h>
#include <linux/pm_runtime.h>
#include <linux/property.h>
#include <linux/soc/qcom/geni-se.h>
#include <linux/spi/spi.h>
#include <linux/spinlock.h>
/* SPI SE specific registers and respective register fields */
#define SE_SPI_CPHA 0x224
#define CPHA BIT(0)
#define SE_SPI_LOOPBACK 0x22c
#define LOOPBACK_ENABLE 0x1
#define NORMAL_MODE 0x0
#define LOOPBACK_MSK GENMASK(1, 0)
#define SE_SPI_CPOL 0x230
#define CPOL BIT(2)
#define SE_SPI_DEMUX_OUTPUT_INV 0x24c
#define CS_DEMUX_OUTPUT_INV_MSK GENMASK(3, 0)
#define SE_SPI_DEMUX_SEL 0x250
#define CS_DEMUX_OUTPUT_SEL GENMASK(3, 0)
#define SE_SPI_TRANS_CFG 0x25c
#define CS_TOGGLE BIT(1)
#define SE_SPI_WORD_LEN 0x268
#define WORD_LEN_MSK GENMASK(9, 0)
#define MIN_WORD_LEN 4
#define SE_SPI_TX_TRANS_LEN 0x26c
#define SE_SPI_RX_TRANS_LEN 0x270
#define TRANS_LEN_MSK GENMASK(23, 0)
#define SE_SPI_PRE_POST_CMD_DLY 0x274
#define SE_SPI_DELAY_COUNTERS 0x278
#define SPI_INTER_WORDS_DELAY_MSK GENMASK(9, 0)
#define SPI_CS_CLK_DELAY_MSK GENMASK(19, 10)
#define SPI_CS_CLK_DELAY_SHFT 10
#define SE_SPI_SLAVE_EN (0x2BC)
#define SPI_SLAVE_EN BIT(0)
/* M_CMD OP codes for SPI */
#define SPI_TX_ONLY 1
#define SPI_RX_ONLY 2
#define SPI_TX_RX 7
#define SPI_CS_ASSERT 8
#define SPI_CS_DEASSERT 9
#define SPI_SCK_ONLY 10
/* M_CMD params for SPI */
#define SPI_PRE_CMD_DELAY BIT(0)
#define TIMESTAMP_BEFORE BIT(1)
#define FRAGMENTATION BIT(2)
#define TIMESTAMP_AFTER BIT(3)
#define POST_CMD_DELAY BIT(4)
#define GSI_LOOPBACK_EN BIT(0)
#define GSI_CS_TOGGLE BIT(3)
#define GSI_CPHA BIT(4)
#define GSI_CPOL BIT(5)
struct spi_geni_master {
struct geni_se se;
struct device *dev;
u32 tx_fifo_depth;
u32 fifo_width_bits;
u32 tx_wm;
u32 last_mode;
unsigned long cur_speed_hz;
unsigned long cur_sclk_hz;
unsigned int cur_bits_per_word;
unsigned int tx_rem_bytes;
unsigned int rx_rem_bytes;
const struct spi_transfer *cur_xfer;
struct completion cs_done;
struct completion cancel_done;
struct completion abort_done;
struct completion tx_reset_done;
struct completion rx_reset_done;
unsigned int oversampling;
spinlock_t lock;
int irq;
bool cs_flag;
2020-12-18 06:29:12 +08:00
bool abort_failed;
struct dma_chan *tx;
struct dma_chan *rx;
int cur_xfer_mode;
};
static void spi_slv_setup(struct spi_geni_master *mas)
{
struct geni_se *se = &mas->se;
writel(SPI_SLAVE_EN, se->base + SE_SPI_SLAVE_EN);
writel(GENI_IO_MUX_0_EN, se->base + GENI_OUTPUT_CTRL);
writel(START_TRIGGER, se->base + SE_GENI_CFG_SEQ_START);
dev_dbg(mas->dev, "spi slave setup done\n");
}
static int get_spi_clk_cfg(unsigned int speed_hz,
struct spi_geni_master *mas,
unsigned int *clk_idx,
unsigned int *clk_div)
{
unsigned long sclk_freq;
unsigned int actual_hz;
int ret;
ret = geni_se_clk_freq_match(&mas->se,
speed_hz * mas->oversampling,
clk_idx, &sclk_freq, false);
if (ret) {
dev_err(mas->dev, "Failed(%d) to find src clk for %dHz\n",
ret, speed_hz);
return ret;
}
*clk_div = DIV_ROUND_UP(sclk_freq, mas->oversampling * speed_hz);
actual_hz = sclk_freq / (mas->oversampling * *clk_div);
dev_dbg(mas->dev, "req %u=>%u sclk %lu, idx %d, div %d\n", speed_hz,
actual_hz, sclk_freq, *clk_idx, *clk_div);
ret = dev_pm_opp_set_rate(mas->dev, sclk_freq);
if (ret)
dev_err(mas->dev, "dev_pm_opp_set_rate failed %d\n", ret);
else
mas->cur_sclk_hz = sclk_freq;
return ret;
}
static void handle_se_timeout(struct spi_controller *spi,
struct spi_message *msg)
{
struct spi_geni_master *mas = spi_controller_get_devdata(spi);
unsigned long time_left;
struct geni_se *se = &mas->se;
const struct spi_transfer *xfer;
spin_lock_irq(&mas->lock);
if (mas->cur_xfer_mode == GENI_SE_FIFO)
writel(0, se->base + SE_GENI_TX_WATERMARK_REG);
xfer = mas->cur_xfer;
mas->cur_xfer = NULL;
if (spi->target) {
/*
* skip CMD Cancel sequnece since spi target
* doesn`t support CMD Cancel sequnece
*/
spin_unlock_irq(&mas->lock);
goto reset_if_dma;
}
reinit_completion(&mas->cancel_done);
geni_se_cancel_m_cmd(se);
spin_unlock_irq(&mas->lock);
time_left = wait_for_completion_timeout(&mas->cancel_done, HZ);
if (time_left)
goto reset_if_dma;
spin_lock_irq(&mas->lock);
reinit_completion(&mas->abort_done);
geni_se_abort_m_cmd(se);
spin_unlock_irq(&mas->lock);
time_left = wait_for_completion_timeout(&mas->abort_done, HZ);
2020-12-18 06:29:12 +08:00
if (!time_left) {
dev_err(mas->dev, "Failed to cancel/abort m_cmd\n");
2020-12-18 06:29:12 +08:00
/*
* No need for a lock since SPI core has a lock and we never
* access this from an interrupt.
*/
mas->abort_failed = true;
}
reset_if_dma:
if (mas->cur_xfer_mode == GENI_SE_DMA) {
if (xfer) {
if (xfer->tx_buf) {
spin_lock_irq(&mas->lock);
reinit_completion(&mas->tx_reset_done);
writel(1, se->base + SE_DMA_TX_FSM_RST);
spin_unlock_irq(&mas->lock);
time_left = wait_for_completion_timeout(&mas->tx_reset_done, HZ);
if (!time_left)
dev_err(mas->dev, "DMA TX RESET failed\n");
}
if (xfer->rx_buf) {
spin_lock_irq(&mas->lock);
reinit_completion(&mas->rx_reset_done);
writel(1, se->base + SE_DMA_RX_FSM_RST);
spin_unlock_irq(&mas->lock);
time_left = wait_for_completion_timeout(&mas->rx_reset_done, HZ);
if (!time_left)
dev_err(mas->dev, "DMA RX RESET failed\n");
}
} else {
/*
* This can happen if a timeout happened and we had to wait
* for lock in this function because isr was holding the lock
* and handling transfer completion at that time.
*/
dev_warn(mas->dev, "Cancel/Abort on completed SPI transfer\n");
}
}
2020-12-18 06:29:12 +08:00
}
static void handle_gpi_timeout(struct spi_controller *spi, struct spi_message *msg)
{
struct spi_geni_master *mas = spi_controller_get_devdata(spi);
dmaengine_terminate_sync(mas->tx);
dmaengine_terminate_sync(mas->rx);
}
static void spi_geni_handle_err(struct spi_controller *spi, struct spi_message *msg)
{
struct spi_geni_master *mas = spi_controller_get_devdata(spi);
switch (mas->cur_xfer_mode) {
case GENI_SE_FIFO:
case GENI_SE_DMA:
handle_se_timeout(spi, msg);
break;
case GENI_GPI_DMA:
handle_gpi_timeout(spi, msg);
break;
default:
dev_err(mas->dev, "Abort on Mode:%d not supported", mas->cur_xfer_mode);
}
}
2020-12-18 06:29:12 +08:00
static bool spi_geni_is_abort_still_pending(struct spi_geni_master *mas)
{
struct geni_se *se = &mas->se;
u32 m_irq, m_irq_en;
if (!mas->abort_failed)
return false;
/*
* The only known case where a transfer times out and then a cancel
* times out then an abort times out is if something is blocking our
* interrupt handler from running. Avoid starting any new transfers
* until that sorts itself out.
*/
spin_lock_irq(&mas->lock);
m_irq = readl(se->base + SE_GENI_M_IRQ_STATUS);
m_irq_en = readl(se->base + SE_GENI_M_IRQ_EN);
spin_unlock_irq(&mas->lock);
if (m_irq & m_irq_en) {
dev_err(mas->dev, "Interrupts pending after abort: %#010x\n",
m_irq & m_irq_en);
return true;
}
/*
* If we're here the problem resolved itself so no need to check more
* on future transfers.
*/
mas->abort_failed = false;
return false;
}
static void spi_geni_set_cs(struct spi_device *slv, bool set_flag)
{
struct spi_geni_master *mas = spi_controller_get_devdata(slv->controller);
struct spi_controller *spi = dev_get_drvdata(mas->dev);
struct geni_se *se = &mas->se;
unsigned long time_left;
if (!(slv->mode & SPI_CS_HIGH))
set_flag = !set_flag;
if (set_flag == mas->cs_flag)
return;
2020-12-18 06:29:12 +08:00
pm_runtime_get_sync(mas->dev);
if (spi_geni_is_abort_still_pending(mas)) {
dev_err(mas->dev, "Can't set chip select\n");
goto exit;
}
spi: spi-geni-qcom: Mo' betta locking If you added a bit of a delay (like a trace_printk) into the ISR for the spi-geni-qcom driver, you would suddenly start seeing some errors spit out. The problem was that, though the ISR itself held a lock, other parts of the driver didn't always grab the lock. One example race was this: CPU0 CPU1 ---- ---- spi_geni_set_cs() mas->cur_mcmd = CMD_CS; geni_se_setup_m_cmd(...) wait_for_completion_timeout(&xfer_done); <INTERRUPT> geni_spi_isr() complete(&xfer_done); <wakeup> pm_runtime_put(mas->dev); ... // back to SPI core spi_geni_transfer_one() setup_fifo_xfer() mas->cur_mcmd = CMD_XFER; mas->cur_cmd = CMD_NONE; // bad! return IRQ_HANDLED; Let's fix this. Before we start messing with hardware, we'll grab the lock to make sure that the IRQ handler from some previous command has really finished. We don't need to hold the lock unless we're in a state where more interrupts can come in, but we at least need to make sure the previous IRQ is done. This lock is used exclusively to prevent the IRQ handler and non-IRQ from stomping on each other. The SPI core handles all other mutual exclusion. As part of this, we change the way that the IRQ handler detects spurious interrupts. Previously we checked for our state variable being set to IRQ_NONE, but that was done outside the spinlock. We could move it into the spinlock, but instead let's just change it to look for the lack of any IRQ status bits being set. This can be done outside the lock--the hardware certainly isn't grabbing or looking at the spinlock when it updates its status register. It's possible that this will fix real (but very rare) errors seen in the field that look like: irq ...: nobody cared (try booting with the "irqpoll" option) NOTE: an alternate strategy considered here was to always make the complete() / spi_finalize_current_transfer() the very last thing in our IRQ handler. With such a change you could consider that we could be "lockless". In that case, though, we'd have to be very careful w/ memory barriers so we made sure we didn't have any bugs with weakly ordered memory. Using spinlocks makes the driver much easier to understand. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-18 23:06:23 +08:00
spin_lock_irq(&mas->lock);
spi: spi-geni-qcom: Don't try to set CS if an xfer is pending If we get a timeout sending then this happens: spi_transfer_one_message() ->transfer_one() AKA spi_geni_transfer_one() setup_fifo_xfer() mas->cur_xfer = non-NULL spi_transfer_wait() => TIMES OUT if (msg->status != -EINPROGRESS) goto out if (ret != 0 ...) spi_set_cs() ->set_cs AKA spi_geni_set_cs() # mas->cur_xfer is non-NULL The above happens _before_ the SPI core calls ->handle_err() AKA handle_fifo_timeout(). Unfortunately that won't work so well on geni. If we got a timeout transferring then it's likely that our interrupt handler is blocked, but we need that same interrupt handler to run and the command channel to be unblocked in order to adjust the chip select. Trying to set the chip select doesn't crash us but ends up confusing our state machine and leads to messages like: Premature done. rx_rem = 32 bpw8 Let's just drop the chip select request in this case. We can detect the case because cur_xfer is non-NULL--it would have been set to NULL in the interrupt handler if the previous transfer had finished. Sure, we might leave the chip select in the wrong state but it's likely it was going to fail anyway and this avoids getting the driver even more confused about what it's doing. The SPI core in general assumes that setting chip select is a simple operation that doesn't fail. Yet another reason to just reconfigure the chip select line as GPIOs. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20201217142842.v3.3.I07afdedcc49655c5d26880f8df9170aac5792378@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-12-18 06:29:13 +08:00
if (mas->cur_xfer) {
dev_err(mas->dev, "Can't set CS when prev xfer running\n");
spin_unlock_irq(&mas->lock);
goto exit;
}
mas->cs_flag = set_flag;
/* set xfer_mode to FIFO to complete cs_done in isr */
mas->cur_xfer_mode = GENI_SE_FIFO;
geni_se_select_mode(se, mas->cur_xfer_mode);
reinit_completion(&mas->cs_done);
if (set_flag)
geni_se_setup_m_cmd(se, SPI_CS_ASSERT, 0);
else
geni_se_setup_m_cmd(se, SPI_CS_DEASSERT, 0);
spi: spi-geni-qcom: Mo' betta locking If you added a bit of a delay (like a trace_printk) into the ISR for the spi-geni-qcom driver, you would suddenly start seeing some errors spit out. The problem was that, though the ISR itself held a lock, other parts of the driver didn't always grab the lock. One example race was this: CPU0 CPU1 ---- ---- spi_geni_set_cs() mas->cur_mcmd = CMD_CS; geni_se_setup_m_cmd(...) wait_for_completion_timeout(&xfer_done); <INTERRUPT> geni_spi_isr() complete(&xfer_done); <wakeup> pm_runtime_put(mas->dev); ... // back to SPI core spi_geni_transfer_one() setup_fifo_xfer() mas->cur_mcmd = CMD_XFER; mas->cur_cmd = CMD_NONE; // bad! return IRQ_HANDLED; Let's fix this. Before we start messing with hardware, we'll grab the lock to make sure that the IRQ handler from some previous command has really finished. We don't need to hold the lock unless we're in a state where more interrupts can come in, but we at least need to make sure the previous IRQ is done. This lock is used exclusively to prevent the IRQ handler and non-IRQ from stomping on each other. The SPI core handles all other mutual exclusion. As part of this, we change the way that the IRQ handler detects spurious interrupts. Previously we checked for our state variable being set to IRQ_NONE, but that was done outside the spinlock. We could move it into the spinlock, but instead let's just change it to look for the lack of any IRQ status bits being set. This can be done outside the lock--the hardware certainly isn't grabbing or looking at the spinlock when it updates its status register. It's possible that this will fix real (but very rare) errors seen in the field that look like: irq ...: nobody cared (try booting with the "irqpoll" option) NOTE: an alternate strategy considered here was to always make the complete() / spi_finalize_current_transfer() the very last thing in our IRQ handler. With such a change you could consider that we could be "lockless". In that case, though, we'd have to be very careful w/ memory barriers so we made sure we didn't have any bugs with weakly ordered memory. Using spinlocks makes the driver much easier to understand. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-18 23:06:23 +08:00
spin_unlock_irq(&mas->lock);
time_left = wait_for_completion_timeout(&mas->cs_done, HZ);
if (!time_left) {
dev_warn(mas->dev, "Timeout setting chip select\n");
handle_se_timeout(spi, NULL);
}
2020-12-18 06:29:12 +08:00
exit:
pm_runtime_put(mas->dev);
}
static void spi_setup_word_len(struct spi_geni_master *mas, u16 mode,
unsigned int bits_per_word)
{
unsigned int pack_words;
bool msb_first = (mode & SPI_LSB_FIRST) ? false : true;
struct geni_se *se = &mas->se;
u32 word_len;
/*
* If bits_per_word isn't a byte aligned value, set the packing to be
* 1 SPI word per FIFO word.
*/
if (!(mas->fifo_width_bits % bits_per_word))
pack_words = mas->fifo_width_bits / bits_per_word;
else
pack_words = 1;
geni_se_config_packing(&mas->se, bits_per_word, pack_words, msb_first,
true, true);
word_len = (bits_per_word - MIN_WORD_LEN) & WORD_LEN_MSK;
writel(word_len, se->base + SE_SPI_WORD_LEN);
}
static int geni_spi_set_clock_and_bw(struct spi_geni_master *mas,
unsigned long clk_hz)
{
u32 clk_sel, m_clk_cfg, idx, div;
struct geni_se *se = &mas->se;
int ret;
spi: spi-geni-qcom: Avoid clock setting if not needed Every SPI transfer could have a different clock rate. The spi-geni-qcom controller code to deal with this was never very well optimized and has always had a lot of code plus some calls into the clk framework which, at the very least, would grab a mutex. However, until recently, the overhead wasn't _too_ much. That changed with commit 0e3b8a81f5df ("spi: spi-geni-qcom: Add interconnect support") we're now calling geni_icc_set_bw(), which leads to a bunch of math plus: geni_icc_set_bw() icc_set_bw() apply_constraints() qcom_icc_set() qcom_icc_bcm_voter_commit() rpmh_invalidate() rpmh_write_batch() ...and those rpmh commands can be a bit beefy if you call them too often. We already know what speed we were running at before, so if we see that nothing has changed let's avoid the whole pile of code. On my hardware, this made spi_geni_prepare_message() drop down from ~145 us down to ~14 us. NOTE: Potentially it might also make sense to add some code into the interconnect framework to avoid executing so much code when bandwidth isn't changing, but even if we did that we still want to short circuit here to save the extra math / clock calls. Acked-by: Mark Brown <broonie@kernel.org> Reviewed-by: Akash Asthana<akashast@codeaurora.org> Fixes: 0e3b8a81f5df ("spi: spi-geni-qcom: Add interconnect support") Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200701174506.1.Icfdcee14649fc0a6c38e87477b28523d4e60bab3@changeid Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-07-02 08:45:07 +08:00
if (clk_hz == mas->cur_speed_hz)
return 0;
ret = get_spi_clk_cfg(clk_hz, mas, &idx, &div);
if (ret) {
dev_err(mas->dev, "Err setting clk to %lu: %d\n", clk_hz, ret);
return ret;
}
/*
* SPI core clock gets configured with the requested frequency
* or the frequency closer to the requested frequency.
* For that reason requested frequency is stored in the
* cur_speed_hz and referred in the consecutive transfer instead
* of calling clk_get_rate() API.
*/
mas->cur_speed_hz = clk_hz;
clk_sel = idx & CLK_SEL_MSK;
m_clk_cfg = (div << CLK_DIV_SHFT) | SER_CLK_EN;
writel(clk_sel, se->base + SE_GENI_CLK_SEL);
writel(m_clk_cfg, se->base + GENI_SER_M_CLK_CFG);
/* Set BW quota for CPU as driver supports FIFO mode only. */
se->icc_paths[CPU_TO_GENI].avg_bw = Bps_to_icc(mas->cur_speed_hz);
ret = geni_icc_set_bw(se);
if (ret)
return ret;
return 0;
}
static int setup_fifo_params(struct spi_device *spi_slv,
struct spi_controller *spi)
{
struct spi_geni_master *mas = spi_controller_get_devdata(spi);
struct geni_se *se = &mas->se;
u32 loopback_cfg = 0, cpol = 0, cpha = 0, demux_output_inv = 0;
u32 demux_sel;
if (mas->last_mode != spi_slv->mode) {
if (spi_slv->mode & SPI_LOOP)
loopback_cfg = LOOPBACK_ENABLE;
if (spi_slv->mode & SPI_CPOL)
cpol = CPOL;
if (spi_slv->mode & SPI_CPHA)
cpha = CPHA;
if (spi_slv->mode & SPI_CS_HIGH)
demux_output_inv = BIT(spi_get_chipselect(spi_slv, 0));
demux_sel = spi_get_chipselect(spi_slv, 0);
mas->cur_bits_per_word = spi_slv->bits_per_word;
spi_setup_word_len(mas, spi_slv->mode, spi_slv->bits_per_word);
writel(loopback_cfg, se->base + SE_SPI_LOOPBACK);
writel(demux_sel, se->base + SE_SPI_DEMUX_SEL);
writel(cpha, se->base + SE_SPI_CPHA);
writel(cpol, se->base + SE_SPI_CPOL);
writel(demux_output_inv, se->base + SE_SPI_DEMUX_OUTPUT_INV);
mas->last_mode = spi_slv->mode;
}
return geni_spi_set_clock_and_bw(mas, spi_slv->max_speed_hz);
}
static void
spi_gsi_callback_result(void *cb, const struct dmaengine_result *result)
{
struct spi_controller *spi = cb;
spi->cur_msg->status = -EIO;
if (result->result != DMA_TRANS_NOERROR) {
dev_err(&spi->dev, "DMA txn failed: %d\n", result->result);
spi_finalize_current_transfer(spi);
return;
}
if (!result->residue) {
spi->cur_msg->status = 0;
dev_dbg(&spi->dev, "DMA txn completed\n");
} else {
dev_err(&spi->dev, "DMA xfer has pending: %d\n", result->residue);
}
spi_finalize_current_transfer(spi);
}
static int setup_gsi_xfer(struct spi_transfer *xfer, struct spi_geni_master *mas,
struct spi_device *spi_slv, struct spi_controller *spi)
{
unsigned long flags = DMA_PREP_INTERRUPT | DMA_CTRL_ACK;
struct dma_slave_config config = {};
struct gpi_spi_config peripheral = {};
struct dma_async_tx_descriptor *tx_desc, *rx_desc;
int ret;
config.peripheral_config = &peripheral;
config.peripheral_size = sizeof(peripheral);
peripheral.set_config = true;
if (xfer->bits_per_word != mas->cur_bits_per_word ||
xfer->speed_hz != mas->cur_speed_hz) {
mas->cur_bits_per_word = xfer->bits_per_word;
mas->cur_speed_hz = xfer->speed_hz;
}
if (xfer->tx_buf && xfer->rx_buf) {
peripheral.cmd = SPI_DUPLEX;
} else if (xfer->tx_buf) {
peripheral.cmd = SPI_TX;
peripheral.rx_len = 0;
} else if (xfer->rx_buf) {
peripheral.cmd = SPI_RX;
if (!(mas->cur_bits_per_word % MIN_WORD_LEN)) {
peripheral.rx_len = ((xfer->len << 3) / mas->cur_bits_per_word);
} else {
int bytes_per_word = (mas->cur_bits_per_word / BITS_PER_BYTE) + 1;
peripheral.rx_len = (xfer->len / bytes_per_word);
}
}
peripheral.loopback_en = !!(spi_slv->mode & SPI_LOOP);
peripheral.clock_pol_high = !!(spi_slv->mode & SPI_CPOL);
peripheral.data_pol_high = !!(spi_slv->mode & SPI_CPHA);
peripheral.cs = spi_get_chipselect(spi_slv, 0);
peripheral.pack_en = true;
peripheral.word_len = xfer->bits_per_word - MIN_WORD_LEN;
ret = get_spi_clk_cfg(mas->cur_speed_hz, mas,
&peripheral.clk_src, &peripheral.clk_div);
if (ret) {
dev_err(mas->dev, "Err in get_spi_clk_cfg() :%d\n", ret);
return ret;
}
if (!xfer->cs_change) {
if (!list_is_last(&xfer->transfer_list, &spi->cur_msg->transfers))
peripheral.fragmentation = FRAGMENTATION;
}
if (peripheral.cmd & SPI_RX) {
dmaengine_slave_config(mas->rx, &config);
rx_desc = dmaengine_prep_slave_sg(mas->rx, xfer->rx_sg.sgl, xfer->rx_sg.nents,
DMA_DEV_TO_MEM, flags);
if (!rx_desc) {
dev_err(mas->dev, "Err setting up rx desc\n");
return -EIO;
}
}
/*
* Prepare the TX always, even for RX or tx_buf being null, we would
* need TX to be prepared per GSI spec
*/
dmaengine_slave_config(mas->tx, &config);
tx_desc = dmaengine_prep_slave_sg(mas->tx, xfer->tx_sg.sgl, xfer->tx_sg.nents,
DMA_MEM_TO_DEV, flags);
if (!tx_desc) {
dev_err(mas->dev, "Err setting up tx desc\n");
return -EIO;
}
tx_desc->callback_result = spi_gsi_callback_result;
tx_desc->callback_param = spi;
if (peripheral.cmd & SPI_RX)
dmaengine_submit(rx_desc);
dmaengine_submit(tx_desc);
if (peripheral.cmd & SPI_RX)
dma_async_issue_pending(mas->rx);
dma_async_issue_pending(mas->tx);
return 1;
}
static u32 get_xfer_len_in_words(struct spi_transfer *xfer,
struct spi_geni_master *mas)
{
u32 len;
if (!(mas->cur_bits_per_word % MIN_WORD_LEN))
len = xfer->len * BITS_PER_BYTE / mas->cur_bits_per_word;
else
len = xfer->len / (mas->cur_bits_per_word / BITS_PER_BYTE + 1);
len &= TRANS_LEN_MSK;
return len;
}
static bool geni_can_dma(struct spi_controller *ctlr,
struct spi_device *slv, struct spi_transfer *xfer)
{
struct spi_geni_master *mas = spi_controller_get_devdata(slv->controller);
u32 len, fifo_size;
if (mas->cur_xfer_mode == GENI_GPI_DMA)
return true;
/* Set SE DMA mode for SPI target. */
if (ctlr->target)
return true;
len = get_xfer_len_in_words(xfer, mas);
fifo_size = mas->tx_fifo_depth * mas->fifo_width_bits / mas->cur_bits_per_word;
if (len > fifo_size)
return true;
else
return false;
}
static int spi_geni_prepare_message(struct spi_controller *spi,
struct spi_message *spi_msg)
{
struct spi_geni_master *mas = spi_controller_get_devdata(spi);
int ret;
switch (mas->cur_xfer_mode) {
case GENI_SE_FIFO:
case GENI_SE_DMA:
if (spi_geni_is_abort_still_pending(mas))
return -EBUSY;
ret = setup_fifo_params(spi_msg->spi, spi);
if (ret)
dev_err(mas->dev, "Couldn't select mode %d\n", ret);
return ret;
2020-12-18 06:29:12 +08:00
case GENI_GPI_DMA:
/* nothing to do for GPI DMA */
return 0;
}
dev_err(mas->dev, "Mode not supported %d", mas->cur_xfer_mode);
return -EINVAL;
}
static int spi_geni_grab_gpi_chan(struct spi_geni_master *mas)
{
int ret;
mas->tx = dma_request_chan(mas->dev, "tx");
if (IS_ERR(mas->tx)) {
ret = dev_err_probe(mas->dev, PTR_ERR(mas->tx),
"Failed to get tx DMA ch\n");
goto err_tx;
}
mas->rx = dma_request_chan(mas->dev, "rx");
if (IS_ERR(mas->rx)) {
ret = dev_err_probe(mas->dev, PTR_ERR(mas->rx),
"Failed to get rx DMA ch\n");
goto err_rx;
}
return 0;
err_rx:
mas->rx = NULL;
dma_release_channel(mas->tx);
err_tx:
mas->tx = NULL;
return ret;
}
static void spi_geni_release_dma_chan(struct spi_geni_master *mas)
{
if (mas->rx) {
dma_release_channel(mas->rx);
mas->rx = NULL;
}
if (mas->tx) {
dma_release_channel(mas->tx);
mas->tx = NULL;
}
}
static int spi_geni_init(struct spi_geni_master *mas)
{
struct spi_master *spi = dev_get_drvdata(mas->dev);
struct geni_se *se = &mas->se;
unsigned int proto, major, minor, ver;
u32 spi_tx_cfg, fifo_disable;
int ret = -ENXIO;
pm_runtime_get_sync(mas->dev);
proto = geni_se_read_proto(se);
if (spi->target) {
if (proto != GENI_SE_SPI_SLAVE) {
dev_err(mas->dev, "Invalid proto %d\n", proto);
goto out_pm;
}
spi_slv_setup(mas);
} else if (proto != GENI_SE_SPI) {
dev_err(mas->dev, "Invalid proto %d\n", proto);
goto out_pm;
}
mas->tx_fifo_depth = geni_se_get_tx_fifo_depth(se);
/* Width of Tx and Rx FIFO is same */
mas->fifo_width_bits = geni_se_get_tx_fifo_width(se);
/*
* Hardware programming guide suggests to configure
* RX FIFO RFR level to fifo_depth-2.
*/
geni_se_init(se, mas->tx_fifo_depth - 3, mas->tx_fifo_depth - 2);
/* Transmit an entire FIFO worth of data per IRQ */
mas->tx_wm = 1;
ver = geni_se_get_qup_hw_version(se);
major = GENI_SE_VERSION_MAJOR(ver);
minor = GENI_SE_VERSION_MINOR(ver);
if (major == 1 && minor == 0)
mas->oversampling = 2;
else
mas->oversampling = 1;
fifo_disable = readl(se->base + GENI_IF_DISABLE_RO) & FIFO_IF_DISABLE;
switch (fifo_disable) {
case 1:
ret = spi_geni_grab_gpi_chan(mas);
if (!ret) { /* success case */
mas->cur_xfer_mode = GENI_GPI_DMA;
geni_se_select_mode(se, GENI_GPI_DMA);
dev_dbg(mas->dev, "Using GPI DMA mode for SPI\n");
break;
} else if (ret == -EPROBE_DEFER) {
goto out_pm;
}
/*
* in case of failure to get gpi dma channel, we can still do the
* FIFO mode, so fallthrough
*/
dev_warn(mas->dev, "FIFO mode disabled, but couldn't get DMA, fall back to FIFO mode\n");
fallthrough;
case 0:
mas->cur_xfer_mode = GENI_SE_FIFO;
geni_se_select_mode(se, GENI_SE_FIFO);
ret = 0;
break;
}
/* We always control CS manually */
if (!spi->target) {
spi_tx_cfg = readl(se->base + SE_SPI_TRANS_CFG);
spi_tx_cfg &= ~CS_TOGGLE;
writel(spi_tx_cfg, se->base + SE_SPI_TRANS_CFG);
}
out_pm:
pm_runtime_put(mas->dev);
return ret;
}
static unsigned int geni_byte_per_fifo_word(struct spi_geni_master *mas)
{
/*
* Calculate how many bytes we'll put in each FIFO word. If the
* transfer words don't pack cleanly into a FIFO word we'll just put
* one transfer word in each FIFO word. If they do pack we'll pack 'em.
*/
if (mas->fifo_width_bits % mas->cur_bits_per_word)
return roundup_pow_of_two(DIV_ROUND_UP(mas->cur_bits_per_word,
BITS_PER_BYTE));
return mas->fifo_width_bits / BITS_PER_BYTE;
}
static bool geni_spi_handle_tx(struct spi_geni_master *mas)
{
struct geni_se *se = &mas->se;
unsigned int max_bytes;
const u8 *tx_buf;
unsigned int bytes_per_fifo_word = geni_byte_per_fifo_word(mas);
unsigned int i = 0;
spi: spi-geni-qcom: Fix geni_spi_isr() NULL dereference in timeout case In commit 7ba9bdcb91f6 ("spi: spi-geni-qcom: Don't keep a local state variable") we changed handle_fifo_timeout() so that we set "mas->cur_xfer" to NULL to make absolutely sure that we don't mess with the buffers from the previous transfer in the timeout case. Unfortunately, this caused the IRQ handler to dereference NULL in some cases. One case: CPU0 CPU1 ---- ---- setup_fifo_xfer() geni_se_setup_m_cmd() <hardware starts transfer> <transfer completes in hardware> <hardware sets M_RX_FIFO_WATERMARK_EN in m_irq> ... handle_fifo_timeout() spin_lock_irq(mas->lock) mas->cur_xfer = NULL geni_se_cancel_m_cmd() spin_unlock_irq(mas->lock) geni_spi_isr() spin_lock(mas->lock) if (m_irq & M_RX_FIFO_WATERMARK_EN) geni_spi_handle_rx() mas->cur_xfer NULL dereference! tl;dr: Seriously delayed interrupts for RX/TX can lead to timeout handling setting mas->cur_xfer to NULL. Let's check for the NULL transfer in the TX and RX cases and reset the watermark or clear out the fifo respectively to put the hardware back into a sane state. NOTE: things still could get confused if we get timeouts all the way through handle_fifo_timeout() and then start a new transfer because interrupts from the old transfer / cancel / abort could still be pending. A future patch will help this corner case. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20201217142842.v3.1.I99ee04f0cb823415df59bd4f550d6ff5756e43d6@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-12-18 06:29:11 +08:00
/* Stop the watermark IRQ if nothing to send */
if (!mas->cur_xfer) {
writel(0, se->base + SE_GENI_TX_WATERMARK_REG);
return false;
}
max_bytes = (mas->tx_fifo_depth - mas->tx_wm) * bytes_per_fifo_word;
if (mas->tx_rem_bytes < max_bytes)
max_bytes = mas->tx_rem_bytes;
tx_buf = mas->cur_xfer->tx_buf + mas->cur_xfer->len - mas->tx_rem_bytes;
while (i < max_bytes) {
unsigned int j;
unsigned int bytes_to_write;
u32 fifo_word = 0;
u8 *fifo_byte = (u8 *)&fifo_word;
bytes_to_write = min(bytes_per_fifo_word, max_bytes - i);
for (j = 0; j < bytes_to_write; j++)
fifo_byte[j] = tx_buf[i++];
iowrite32_rep(se->base + SE_GENI_TX_FIFOn, &fifo_word, 1);
}
mas->tx_rem_bytes -= max_bytes;
if (!mas->tx_rem_bytes) {
writel(0, se->base + SE_GENI_TX_WATERMARK_REG);
return false;
}
return true;
}
static void geni_spi_handle_rx(struct spi_geni_master *mas)
{
struct geni_se *se = &mas->se;
u32 rx_fifo_status;
unsigned int rx_bytes;
unsigned int rx_last_byte_valid;
u8 *rx_buf;
unsigned int bytes_per_fifo_word = geni_byte_per_fifo_word(mas);
unsigned int i = 0;
rx_fifo_status = readl(se->base + SE_GENI_RX_FIFO_STATUS);
rx_bytes = (rx_fifo_status & RX_FIFO_WC_MSK) * bytes_per_fifo_word;
if (rx_fifo_status & RX_LAST) {
rx_last_byte_valid = rx_fifo_status & RX_LAST_BYTE_VALID_MSK;
rx_last_byte_valid >>= RX_LAST_BYTE_VALID_SHFT;
if (rx_last_byte_valid && rx_last_byte_valid < 4)
rx_bytes -= bytes_per_fifo_word - rx_last_byte_valid;
}
spi: spi-geni-qcom: Fix geni_spi_isr() NULL dereference in timeout case In commit 7ba9bdcb91f6 ("spi: spi-geni-qcom: Don't keep a local state variable") we changed handle_fifo_timeout() so that we set "mas->cur_xfer" to NULL to make absolutely sure that we don't mess with the buffers from the previous transfer in the timeout case. Unfortunately, this caused the IRQ handler to dereference NULL in some cases. One case: CPU0 CPU1 ---- ---- setup_fifo_xfer() geni_se_setup_m_cmd() <hardware starts transfer> <transfer completes in hardware> <hardware sets M_RX_FIFO_WATERMARK_EN in m_irq> ... handle_fifo_timeout() spin_lock_irq(mas->lock) mas->cur_xfer = NULL geni_se_cancel_m_cmd() spin_unlock_irq(mas->lock) geni_spi_isr() spin_lock(mas->lock) if (m_irq & M_RX_FIFO_WATERMARK_EN) geni_spi_handle_rx() mas->cur_xfer NULL dereference! tl;dr: Seriously delayed interrupts for RX/TX can lead to timeout handling setting mas->cur_xfer to NULL. Let's check for the NULL transfer in the TX and RX cases and reset the watermark or clear out the fifo respectively to put the hardware back into a sane state. NOTE: things still could get confused if we get timeouts all the way through handle_fifo_timeout() and then start a new transfer because interrupts from the old transfer / cancel / abort could still be pending. A future patch will help this corner case. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20201217142842.v3.1.I99ee04f0cb823415df59bd4f550d6ff5756e43d6@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-12-18 06:29:11 +08:00
/* Clear out the FIFO and bail if nowhere to put it */
if (!mas->cur_xfer) {
for (i = 0; i < DIV_ROUND_UP(rx_bytes, bytes_per_fifo_word); i++)
readl(se->base + SE_GENI_RX_FIFOn);
return;
}
if (mas->rx_rem_bytes < rx_bytes)
rx_bytes = mas->rx_rem_bytes;
rx_buf = mas->cur_xfer->rx_buf + mas->cur_xfer->len - mas->rx_rem_bytes;
while (i < rx_bytes) {
u32 fifo_word = 0;
u8 *fifo_byte = (u8 *)&fifo_word;
unsigned int bytes_to_read;
unsigned int j;
bytes_to_read = min(bytes_per_fifo_word, rx_bytes - i);
ioread32_rep(se->base + SE_GENI_RX_FIFOn, &fifo_word, 1);
for (j = 0; j < bytes_to_read; j++)
rx_buf[i++] = fifo_byte[j];
}
mas->rx_rem_bytes -= rx_bytes;
}
static int setup_se_xfer(struct spi_transfer *xfer,
struct spi_geni_master *mas,
u16 mode, struct spi_controller *spi)
{
u32 m_cmd = 0;
u32 len;
struct geni_se *se = &mas->se;
int ret;
spi: spi-geni-qcom: Mo' betta locking If you added a bit of a delay (like a trace_printk) into the ISR for the spi-geni-qcom driver, you would suddenly start seeing some errors spit out. The problem was that, though the ISR itself held a lock, other parts of the driver didn't always grab the lock. One example race was this: CPU0 CPU1 ---- ---- spi_geni_set_cs() mas->cur_mcmd = CMD_CS; geni_se_setup_m_cmd(...) wait_for_completion_timeout(&xfer_done); <INTERRUPT> geni_spi_isr() complete(&xfer_done); <wakeup> pm_runtime_put(mas->dev); ... // back to SPI core spi_geni_transfer_one() setup_fifo_xfer() mas->cur_mcmd = CMD_XFER; mas->cur_cmd = CMD_NONE; // bad! return IRQ_HANDLED; Let's fix this. Before we start messing with hardware, we'll grab the lock to make sure that the IRQ handler from some previous command has really finished. We don't need to hold the lock unless we're in a state where more interrupts can come in, but we at least need to make sure the previous IRQ is done. This lock is used exclusively to prevent the IRQ handler and non-IRQ from stomping on each other. The SPI core handles all other mutual exclusion. As part of this, we change the way that the IRQ handler detects spurious interrupts. Previously we checked for our state variable being set to IRQ_NONE, but that was done outside the spinlock. We could move it into the spinlock, but instead let's just change it to look for the lack of any IRQ status bits being set. This can be done outside the lock--the hardware certainly isn't grabbing or looking at the spinlock when it updates its status register. It's possible that this will fix real (but very rare) errors seen in the field that look like: irq ...: nobody cared (try booting with the "irqpoll" option) NOTE: an alternate strategy considered here was to always make the complete() / spi_finalize_current_transfer() the very last thing in our IRQ handler. With such a change you could consider that we could be "lockless". In that case, though, we'd have to be very careful w/ memory barriers so we made sure we didn't have any bugs with weakly ordered memory. Using spinlocks makes the driver much easier to understand. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-18 23:06:23 +08:00
/*
* Ensure that our interrupt handler isn't still running from some
* prior command before we start messing with the hardware behind
* its back. We don't need to _keep_ the lock here since we're only
* worried about racing with out interrupt handler. The SPI core
* already handles making sure that we're not trying to do two
* transfers at once or setting a chip select and doing a transfer
* concurrently.
*
* NOTE: we actually _can't_ hold the lock here because possibly we
* might call clk_set_rate() which needs to be able to sleep.
*/
spin_lock_irq(&mas->lock);
spin_unlock_irq(&mas->lock);
if (xfer->bits_per_word != mas->cur_bits_per_word) {
spi_setup_word_len(mas, mode, xfer->bits_per_word);
mas->cur_bits_per_word = xfer->bits_per_word;
}
/* Speed and bits per word can be overridden per transfer */
spi: spi-geni-qcom: Avoid clock setting if not needed Every SPI transfer could have a different clock rate. The spi-geni-qcom controller code to deal with this was never very well optimized and has always had a lot of code plus some calls into the clk framework which, at the very least, would grab a mutex. However, until recently, the overhead wasn't _too_ much. That changed with commit 0e3b8a81f5df ("spi: spi-geni-qcom: Add interconnect support") we're now calling geni_icc_set_bw(), which leads to a bunch of math plus: geni_icc_set_bw() icc_set_bw() apply_constraints() qcom_icc_set() qcom_icc_bcm_voter_commit() rpmh_invalidate() rpmh_write_batch() ...and those rpmh commands can be a bit beefy if you call them too often. We already know what speed we were running at before, so if we see that nothing has changed let's avoid the whole pile of code. On my hardware, this made spi_geni_prepare_message() drop down from ~145 us down to ~14 us. NOTE: Potentially it might also make sense to add some code into the interconnect framework to avoid executing so much code when bandwidth isn't changing, but even if we did that we still want to short circuit here to save the extra math / clock calls. Acked-by: Mark Brown <broonie@kernel.org> Reviewed-by: Akash Asthana<akashast@codeaurora.org> Fixes: 0e3b8a81f5df ("spi: spi-geni-qcom: Add interconnect support") Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200701174506.1.Icfdcee14649fc0a6c38e87477b28523d4e60bab3@changeid Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-07-02 08:45:07 +08:00
ret = geni_spi_set_clock_and_bw(mas, xfer->speed_hz);
if (ret)
return ret;
mas->tx_rem_bytes = 0;
mas->rx_rem_bytes = 0;
len = get_xfer_len_in_words(xfer, mas);
mas->cur_xfer = xfer;
if (xfer->tx_buf) {
m_cmd |= SPI_TX_ONLY;
mas->tx_rem_bytes = xfer->len;
writel(len, se->base + SE_SPI_TX_TRANS_LEN);
}
if (xfer->rx_buf) {
m_cmd |= SPI_RX_ONLY;
writel(len, se->base + SE_SPI_RX_TRANS_LEN);
mas->rx_rem_bytes = xfer->len;
}
spi: spi-geni-qcom: Mo' betta locking If you added a bit of a delay (like a trace_printk) into the ISR for the spi-geni-qcom driver, you would suddenly start seeing some errors spit out. The problem was that, though the ISR itself held a lock, other parts of the driver didn't always grab the lock. One example race was this: CPU0 CPU1 ---- ---- spi_geni_set_cs() mas->cur_mcmd = CMD_CS; geni_se_setup_m_cmd(...) wait_for_completion_timeout(&xfer_done); <INTERRUPT> geni_spi_isr() complete(&xfer_done); <wakeup> pm_runtime_put(mas->dev); ... // back to SPI core spi_geni_transfer_one() setup_fifo_xfer() mas->cur_mcmd = CMD_XFER; mas->cur_cmd = CMD_NONE; // bad! return IRQ_HANDLED; Let's fix this. Before we start messing with hardware, we'll grab the lock to make sure that the IRQ handler from some previous command has really finished. We don't need to hold the lock unless we're in a state where more interrupts can come in, but we at least need to make sure the previous IRQ is done. This lock is used exclusively to prevent the IRQ handler and non-IRQ from stomping on each other. The SPI core handles all other mutual exclusion. As part of this, we change the way that the IRQ handler detects spurious interrupts. Previously we checked for our state variable being set to IRQ_NONE, but that was done outside the spinlock. We could move it into the spinlock, but instead let's just change it to look for the lack of any IRQ status bits being set. This can be done outside the lock--the hardware certainly isn't grabbing or looking at the spinlock when it updates its status register. It's possible that this will fix real (but very rare) errors seen in the field that look like: irq ...: nobody cared (try booting with the "irqpoll" option) NOTE: an alternate strategy considered here was to always make the complete() / spi_finalize_current_transfer() the very last thing in our IRQ handler. With such a change you could consider that we could be "lockless". In that case, though, we'd have to be very careful w/ memory barriers so we made sure we didn't have any bugs with weakly ordered memory. Using spinlocks makes the driver much easier to understand. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-18 23:06:23 +08:00
/*
* Select DMA mode if sgt are present; and with only 1 entry
* This is not a serious limitation because the xfer buffers are
* expected to fit into in 1 entry almost always, and if any
* doesn't for any reason we fall back to FIFO mode anyway
*/
if (!xfer->tx_sg.nents && !xfer->rx_sg.nents)
mas->cur_xfer_mode = GENI_SE_FIFO;
else if (xfer->tx_sg.nents > 1 || xfer->rx_sg.nents > 1) {
dev_warn_once(mas->dev, "Doing FIFO, cannot handle tx_nents-%d, rx_nents-%d\n",
xfer->tx_sg.nents, xfer->rx_sg.nents);
mas->cur_xfer_mode = GENI_SE_FIFO;
} else
mas->cur_xfer_mode = GENI_SE_DMA;
geni_se_select_mode(se, mas->cur_xfer_mode);
spi: spi-geni-qcom: Mo' betta locking If you added a bit of a delay (like a trace_printk) into the ISR for the spi-geni-qcom driver, you would suddenly start seeing some errors spit out. The problem was that, though the ISR itself held a lock, other parts of the driver didn't always grab the lock. One example race was this: CPU0 CPU1 ---- ---- spi_geni_set_cs() mas->cur_mcmd = CMD_CS; geni_se_setup_m_cmd(...) wait_for_completion_timeout(&xfer_done); <INTERRUPT> geni_spi_isr() complete(&xfer_done); <wakeup> pm_runtime_put(mas->dev); ... // back to SPI core spi_geni_transfer_one() setup_fifo_xfer() mas->cur_mcmd = CMD_XFER; mas->cur_cmd = CMD_NONE; // bad! return IRQ_HANDLED; Let's fix this. Before we start messing with hardware, we'll grab the lock to make sure that the IRQ handler from some previous command has really finished. We don't need to hold the lock unless we're in a state where more interrupts can come in, but we at least need to make sure the previous IRQ is done. This lock is used exclusively to prevent the IRQ handler and non-IRQ from stomping on each other. The SPI core handles all other mutual exclusion. As part of this, we change the way that the IRQ handler detects spurious interrupts. Previously we checked for our state variable being set to IRQ_NONE, but that was done outside the spinlock. We could move it into the spinlock, but instead let's just change it to look for the lack of any IRQ status bits being set. This can be done outside the lock--the hardware certainly isn't grabbing or looking at the spinlock when it updates its status register. It's possible that this will fix real (but very rare) errors seen in the field that look like: irq ...: nobody cared (try booting with the "irqpoll" option) NOTE: an alternate strategy considered here was to always make the complete() / spi_finalize_current_transfer() the very last thing in our IRQ handler. With such a change you could consider that we could be "lockless". In that case, though, we'd have to be very careful w/ memory barriers so we made sure we didn't have any bugs with weakly ordered memory. Using spinlocks makes the driver much easier to understand. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-18 23:06:23 +08:00
/*
* Lock around right before we start the transfer since our
* interrupt could come in at any time now.
*/
spin_lock_irq(&mas->lock);
geni_se_setup_m_cmd(se, m_cmd, FRAGMENTATION);
if (mas->cur_xfer_mode == GENI_SE_DMA) {
if (m_cmd & SPI_RX_ONLY)
geni_se_rx_init_dma(se, sg_dma_address(xfer->rx_sg.sgl),
sg_dma_len(xfer->rx_sg.sgl));
if (m_cmd & SPI_TX_ONLY)
geni_se_tx_init_dma(se, sg_dma_address(xfer->tx_sg.sgl),
sg_dma_len(xfer->tx_sg.sgl));
} else if (m_cmd & SPI_TX_ONLY) {
if (geni_spi_handle_tx(mas))
writel(mas->tx_wm, se->base + SE_GENI_TX_WATERMARK_REG);
}
spi: spi-geni-qcom: Mo' betta locking If you added a bit of a delay (like a trace_printk) into the ISR for the spi-geni-qcom driver, you would suddenly start seeing some errors spit out. The problem was that, though the ISR itself held a lock, other parts of the driver didn't always grab the lock. One example race was this: CPU0 CPU1 ---- ---- spi_geni_set_cs() mas->cur_mcmd = CMD_CS; geni_se_setup_m_cmd(...) wait_for_completion_timeout(&xfer_done); <INTERRUPT> geni_spi_isr() complete(&xfer_done); <wakeup> pm_runtime_put(mas->dev); ... // back to SPI core spi_geni_transfer_one() setup_fifo_xfer() mas->cur_mcmd = CMD_XFER; mas->cur_cmd = CMD_NONE; // bad! return IRQ_HANDLED; Let's fix this. Before we start messing with hardware, we'll grab the lock to make sure that the IRQ handler from some previous command has really finished. We don't need to hold the lock unless we're in a state where more interrupts can come in, but we at least need to make sure the previous IRQ is done. This lock is used exclusively to prevent the IRQ handler and non-IRQ from stomping on each other. The SPI core handles all other mutual exclusion. As part of this, we change the way that the IRQ handler detects spurious interrupts. Previously we checked for our state variable being set to IRQ_NONE, but that was done outside the spinlock. We could move it into the spinlock, but instead let's just change it to look for the lack of any IRQ status bits being set. This can be done outside the lock--the hardware certainly isn't grabbing or looking at the spinlock when it updates its status register. It's possible that this will fix real (but very rare) errors seen in the field that look like: irq ...: nobody cared (try booting with the "irqpoll" option) NOTE: an alternate strategy considered here was to always make the complete() / spi_finalize_current_transfer() the very last thing in our IRQ handler. With such a change you could consider that we could be "lockless". In that case, though, we'd have to be very careful w/ memory barriers so we made sure we didn't have any bugs with weakly ordered memory. Using spinlocks makes the driver much easier to understand. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-18 23:06:23 +08:00
spin_unlock_irq(&mas->lock);
return ret;
}
static int spi_geni_transfer_one(struct spi_controller *spi,
struct spi_device *slv,
struct spi_transfer *xfer)
{
struct spi_geni_master *mas = spi_controller_get_devdata(spi);
int ret;
2020-12-18 06:29:12 +08:00
if (spi_geni_is_abort_still_pending(mas))
return -EBUSY;
/* Terminate and return success for 0 byte length transfer */
if (!xfer->len)
return 0;
if (mas->cur_xfer_mode == GENI_SE_FIFO || mas->cur_xfer_mode == GENI_SE_DMA) {
ret = setup_se_xfer(xfer, mas, slv->mode, spi);
/* SPI framework expects +ve ret code to wait for transfer complete */
if (!ret)
ret = 1;
return ret;
}
return setup_gsi_xfer(xfer, mas, slv, spi);
}
static irqreturn_t geni_spi_isr(int irq, void *data)
{
struct spi_controller *spi = data;
struct spi_geni_master *mas = spi_controller_get_devdata(spi);
struct geni_se *se = &mas->se;
u32 m_irq;
spi: spi-geni-qcom: Mo' betta locking If you added a bit of a delay (like a trace_printk) into the ISR for the spi-geni-qcom driver, you would suddenly start seeing some errors spit out. The problem was that, though the ISR itself held a lock, other parts of the driver didn't always grab the lock. One example race was this: CPU0 CPU1 ---- ---- spi_geni_set_cs() mas->cur_mcmd = CMD_CS; geni_se_setup_m_cmd(...) wait_for_completion_timeout(&xfer_done); <INTERRUPT> geni_spi_isr() complete(&xfer_done); <wakeup> pm_runtime_put(mas->dev); ... // back to SPI core spi_geni_transfer_one() setup_fifo_xfer() mas->cur_mcmd = CMD_XFER; mas->cur_cmd = CMD_NONE; // bad! return IRQ_HANDLED; Let's fix this. Before we start messing with hardware, we'll grab the lock to make sure that the IRQ handler from some previous command has really finished. We don't need to hold the lock unless we're in a state where more interrupts can come in, but we at least need to make sure the previous IRQ is done. This lock is used exclusively to prevent the IRQ handler and non-IRQ from stomping on each other. The SPI core handles all other mutual exclusion. As part of this, we change the way that the IRQ handler detects spurious interrupts. Previously we checked for our state variable being set to IRQ_NONE, but that was done outside the spinlock. We could move it into the spinlock, but instead let's just change it to look for the lack of any IRQ status bits being set. This can be done outside the lock--the hardware certainly isn't grabbing or looking at the spinlock when it updates its status register. It's possible that this will fix real (but very rare) errors seen in the field that look like: irq ...: nobody cared (try booting with the "irqpoll" option) NOTE: an alternate strategy considered here was to always make the complete() / spi_finalize_current_transfer() the very last thing in our IRQ handler. With such a change you could consider that we could be "lockless". In that case, though, we'd have to be very careful w/ memory barriers so we made sure we didn't have any bugs with weakly ordered memory. Using spinlocks makes the driver much easier to understand. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-18 23:06:23 +08:00
m_irq = readl(se->base + SE_GENI_M_IRQ_STATUS);
if (!m_irq)
return IRQ_NONE;
if (m_irq & (M_CMD_OVERRUN_EN | M_ILLEGAL_CMD_EN | M_CMD_FAILURE_EN |
M_RX_FIFO_RD_ERR_EN | M_RX_FIFO_WR_ERR_EN |
M_TX_FIFO_RD_ERR_EN | M_TX_FIFO_WR_ERR_EN))
dev_warn(mas->dev, "Unexpected IRQ err status %#010x\n", m_irq);
spin_lock(&mas->lock);
if (mas->cur_xfer_mode == GENI_SE_FIFO) {
if ((m_irq & M_RX_FIFO_WATERMARK_EN) || (m_irq & M_RX_FIFO_LAST_EN))
geni_spi_handle_rx(mas);
if (m_irq & M_TX_FIFO_WATERMARK_EN)
geni_spi_handle_tx(mas);
if (m_irq & M_CMD_DONE_EN) {
if (mas->cur_xfer) {
spi_finalize_current_transfer(spi);
mas->cur_xfer = NULL;
/*
* If this happens, then a CMD_DONE came before all the
* Tx buffer bytes were sent out. This is unusual, log
* this condition and disable the WM interrupt to
* prevent the system from stalling due an interrupt
* storm.
*
* If this happens when all Rx bytes haven't been
* received, log the condition. The only known time
* this can happen is if bits_per_word != 8 and some
* registers that expect xfer lengths in num spi_words
* weren't written correctly.
*/
if (mas->tx_rem_bytes) {
writel(0, se->base + SE_GENI_TX_WATERMARK_REG);
dev_err(mas->dev, "Premature done. tx_rem = %d bpw%d\n",
mas->tx_rem_bytes, mas->cur_bits_per_word);
}
if (mas->rx_rem_bytes)
dev_err(mas->dev, "Premature done. rx_rem = %d bpw%d\n",
mas->rx_rem_bytes, mas->cur_bits_per_word);
} else {
complete(&mas->cs_done);
}
}
} else if (mas->cur_xfer_mode == GENI_SE_DMA) {
const struct spi_transfer *xfer = mas->cur_xfer;
u32 dma_tx_status = readl_relaxed(se->base + SE_DMA_TX_IRQ_STAT);
u32 dma_rx_status = readl_relaxed(se->base + SE_DMA_RX_IRQ_STAT);
if (dma_tx_status)
writel(dma_tx_status, se->base + SE_DMA_TX_IRQ_CLR);
if (dma_rx_status)
writel(dma_rx_status, se->base + SE_DMA_RX_IRQ_CLR);
if (dma_tx_status & TX_DMA_DONE)
mas->tx_rem_bytes = 0;
if (dma_rx_status & RX_DMA_DONE)
mas->rx_rem_bytes = 0;
if (dma_tx_status & TX_RESET_DONE)
complete(&mas->tx_reset_done);
if (dma_rx_status & RX_RESET_DONE)
complete(&mas->rx_reset_done);
if (!mas->tx_rem_bytes && !mas->rx_rem_bytes && xfer) {
spi_finalize_current_transfer(spi);
mas->cur_xfer = NULL;
}
}
if (m_irq & M_CMD_CANCEL_EN)
complete(&mas->cancel_done);
if (m_irq & M_CMD_ABORT_EN)
complete(&mas->abort_done);
spi: spi-geni-qcom: Mo' betta locking If you added a bit of a delay (like a trace_printk) into the ISR for the spi-geni-qcom driver, you would suddenly start seeing some errors spit out. The problem was that, though the ISR itself held a lock, other parts of the driver didn't always grab the lock. One example race was this: CPU0 CPU1 ---- ---- spi_geni_set_cs() mas->cur_mcmd = CMD_CS; geni_se_setup_m_cmd(...) wait_for_completion_timeout(&xfer_done); <INTERRUPT> geni_spi_isr() complete(&xfer_done); <wakeup> pm_runtime_put(mas->dev); ... // back to SPI core spi_geni_transfer_one() setup_fifo_xfer() mas->cur_mcmd = CMD_XFER; mas->cur_cmd = CMD_NONE; // bad! return IRQ_HANDLED; Let's fix this. Before we start messing with hardware, we'll grab the lock to make sure that the IRQ handler from some previous command has really finished. We don't need to hold the lock unless we're in a state where more interrupts can come in, but we at least need to make sure the previous IRQ is done. This lock is used exclusively to prevent the IRQ handler and non-IRQ from stomping on each other. The SPI core handles all other mutual exclusion. As part of this, we change the way that the IRQ handler detects spurious interrupts. Previously we checked for our state variable being set to IRQ_NONE, but that was done outside the spinlock. We could move it into the spinlock, but instead let's just change it to look for the lack of any IRQ status bits being set. This can be done outside the lock--the hardware certainly isn't grabbing or looking at the spinlock when it updates its status register. It's possible that this will fix real (but very rare) errors seen in the field that look like: irq ...: nobody cared (try booting with the "irqpoll" option) NOTE: an alternate strategy considered here was to always make the complete() / spi_finalize_current_transfer() the very last thing in our IRQ handler. With such a change you could consider that we could be "lockless". In that case, though, we'd have to be very careful w/ memory barriers so we made sure we didn't have any bugs with weakly ordered memory. Using spinlocks makes the driver much easier to understand. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-18 23:06:23 +08:00
/*
* It's safe or a good idea to Ack all of our interrupts at the end
* of the function. Specifically:
spi: spi-geni-qcom: Mo' betta locking If you added a bit of a delay (like a trace_printk) into the ISR for the spi-geni-qcom driver, you would suddenly start seeing some errors spit out. The problem was that, though the ISR itself held a lock, other parts of the driver didn't always grab the lock. One example race was this: CPU0 CPU1 ---- ---- spi_geni_set_cs() mas->cur_mcmd = CMD_CS; geni_se_setup_m_cmd(...) wait_for_completion_timeout(&xfer_done); <INTERRUPT> geni_spi_isr() complete(&xfer_done); <wakeup> pm_runtime_put(mas->dev); ... // back to SPI core spi_geni_transfer_one() setup_fifo_xfer() mas->cur_mcmd = CMD_XFER; mas->cur_cmd = CMD_NONE; // bad! return IRQ_HANDLED; Let's fix this. Before we start messing with hardware, we'll grab the lock to make sure that the IRQ handler from some previous command has really finished. We don't need to hold the lock unless we're in a state where more interrupts can come in, but we at least need to make sure the previous IRQ is done. This lock is used exclusively to prevent the IRQ handler and non-IRQ from stomping on each other. The SPI core handles all other mutual exclusion. As part of this, we change the way that the IRQ handler detects spurious interrupts. Previously we checked for our state variable being set to IRQ_NONE, but that was done outside the spinlock. We could move it into the spinlock, but instead let's just change it to look for the lack of any IRQ status bits being set. This can be done outside the lock--the hardware certainly isn't grabbing or looking at the spinlock when it updates its status register. It's possible that this will fix real (but very rare) errors seen in the field that look like: irq ...: nobody cared (try booting with the "irqpoll" option) NOTE: an alternate strategy considered here was to always make the complete() / spi_finalize_current_transfer() the very last thing in our IRQ handler. With such a change you could consider that we could be "lockless". In that case, though, we'd have to be very careful w/ memory barriers so we made sure we didn't have any bugs with weakly ordered memory. Using spinlocks makes the driver much easier to understand. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-18 23:06:23 +08:00
* - M_CMD_DONE_EN / M_RX_FIFO_LAST_EN: Edge triggered interrupts and
* clearing Acks. Clearing at the end relies on nobody else having
* started a new transfer yet or else we could be clearing _their_
* done bit, but everyone grabs the spinlock before starting a new
* transfer.
* - M_RX_FIFO_WATERMARK_EN / M_TX_FIFO_WATERMARK_EN: These appear
* to be "latched level" interrupts so it's important to clear them
* _after_ you've handled the condition and always safe to do so
* since they'll re-assert if they're still happening.
*/
writel(m_irq, se->base + SE_GENI_M_IRQ_CLEAR);
spi: spi-geni-qcom: Mo' betta locking If you added a bit of a delay (like a trace_printk) into the ISR for the spi-geni-qcom driver, you would suddenly start seeing some errors spit out. The problem was that, though the ISR itself held a lock, other parts of the driver didn't always grab the lock. One example race was this: CPU0 CPU1 ---- ---- spi_geni_set_cs() mas->cur_mcmd = CMD_CS; geni_se_setup_m_cmd(...) wait_for_completion_timeout(&xfer_done); <INTERRUPT> geni_spi_isr() complete(&xfer_done); <wakeup> pm_runtime_put(mas->dev); ... // back to SPI core spi_geni_transfer_one() setup_fifo_xfer() mas->cur_mcmd = CMD_XFER; mas->cur_cmd = CMD_NONE; // bad! return IRQ_HANDLED; Let's fix this. Before we start messing with hardware, we'll grab the lock to make sure that the IRQ handler from some previous command has really finished. We don't need to hold the lock unless we're in a state where more interrupts can come in, but we at least need to make sure the previous IRQ is done. This lock is used exclusively to prevent the IRQ handler and non-IRQ from stomping on each other. The SPI core handles all other mutual exclusion. As part of this, we change the way that the IRQ handler detects spurious interrupts. Previously we checked for our state variable being set to IRQ_NONE, but that was done outside the spinlock. We could move it into the spinlock, but instead let's just change it to look for the lack of any IRQ status bits being set. This can be done outside the lock--the hardware certainly isn't grabbing or looking at the spinlock when it updates its status register. It's possible that this will fix real (but very rare) errors seen in the field that look like: irq ...: nobody cared (try booting with the "irqpoll" option) NOTE: an alternate strategy considered here was to always make the complete() / spi_finalize_current_transfer() the very last thing in our IRQ handler. With such a change you could consider that we could be "lockless". In that case, though, we'd have to be very careful w/ memory barriers so we made sure we didn't have any bugs with weakly ordered memory. Using spinlocks makes the driver much easier to understand. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-18 23:06:23 +08:00
spin_unlock(&mas->lock);
spi: spi-geni-qcom: Mo' betta locking If you added a bit of a delay (like a trace_printk) into the ISR for the spi-geni-qcom driver, you would suddenly start seeing some errors spit out. The problem was that, though the ISR itself held a lock, other parts of the driver didn't always grab the lock. One example race was this: CPU0 CPU1 ---- ---- spi_geni_set_cs() mas->cur_mcmd = CMD_CS; geni_se_setup_m_cmd(...) wait_for_completion_timeout(&xfer_done); <INTERRUPT> geni_spi_isr() complete(&xfer_done); <wakeup> pm_runtime_put(mas->dev); ... // back to SPI core spi_geni_transfer_one() setup_fifo_xfer() mas->cur_mcmd = CMD_XFER; mas->cur_cmd = CMD_NONE; // bad! return IRQ_HANDLED; Let's fix this. Before we start messing with hardware, we'll grab the lock to make sure that the IRQ handler from some previous command has really finished. We don't need to hold the lock unless we're in a state where more interrupts can come in, but we at least need to make sure the previous IRQ is done. This lock is used exclusively to prevent the IRQ handler and non-IRQ from stomping on each other. The SPI core handles all other mutual exclusion. As part of this, we change the way that the IRQ handler detects spurious interrupts. Previously we checked for our state variable being set to IRQ_NONE, but that was done outside the spinlock. We could move it into the spinlock, but instead let's just change it to look for the lack of any IRQ status bits being set. This can be done outside the lock--the hardware certainly isn't grabbing or looking at the spinlock when it updates its status register. It's possible that this will fix real (but very rare) errors seen in the field that look like: irq ...: nobody cared (try booting with the "irqpoll" option) NOTE: an alternate strategy considered here was to always make the complete() / spi_finalize_current_transfer() the very last thing in our IRQ handler. With such a change you could consider that we could be "lockless". In that case, though, we'd have to be very careful w/ memory barriers so we made sure we didn't have any bugs with weakly ordered memory. Using spinlocks makes the driver much easier to understand. Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-18 23:06:23 +08:00
return IRQ_HANDLED;
}
static int spi_geni_probe(struct platform_device *pdev)
{
int ret, irq;
struct spi_controller *spi;
struct spi_geni_master *mas;
void __iomem *base;
struct clk *clk;
struct device *dev = &pdev->dev;
irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(64));
if (ret)
return dev_err_probe(dev, ret, "could not set DMA mask\n");
base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(base))
return PTR_ERR(base);
clk = devm_clk_get(dev, "se");
if (IS_ERR(clk))
return PTR_ERR(clk);
spi = devm_spi_alloc_host(dev, sizeof(*mas));
if (!spi)
return -ENOMEM;
platform_set_drvdata(pdev, spi);
mas = spi_controller_get_devdata(spi);
mas->irq = irq;
mas->dev = dev;
mas->se.dev = dev;
mas->se.wrapper = dev_get_drvdata(dev->parent);
mas->se.base = base;
mas->se.clk = clk;
ret = devm_pm_opp_set_clkname(&pdev->dev, "se");
if (ret)
return ret;
/* OPP table is optional */
ret = devm_pm_opp_of_add_table(&pdev->dev);
if (ret && ret != -ENODEV) {
dev_err(&pdev->dev, "invalid OPP table in device tree\n");
return ret;
}
spi->bus_num = -1;
spi->dev.of_node = dev->of_node;
spi->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LOOP | SPI_CS_HIGH;
spi->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
spi->num_chipselect = 4;
spi->max_speed_hz = 50000000;
spi->max_dma_len = 0xffff0; /* 24 bits for tx/rx dma length */
spi->prepare_message = spi_geni_prepare_message;
spi->transfer_one = spi_geni_transfer_one;
spi->can_dma = geni_can_dma;
spi->dma_map_dev = dev->parent;
spi->auto_runtime_pm = true;
spi->handle_err = spi_geni_handle_err;
spi->use_gpio_descriptors = true;
init_completion(&mas->cs_done);
init_completion(&mas->cancel_done);
init_completion(&mas->abort_done);
init_completion(&mas->tx_reset_done);
init_completion(&mas->rx_reset_done);
spin_lock_init(&mas->lock);
pm_runtime_use_autosuspend(&pdev->dev);
pm_runtime_set_autosuspend_delay(&pdev->dev, 250);
pm_runtime_enable(dev);
if (device_property_read_bool(&pdev->dev, "spi-slave"))
spi->target = true;
ret = geni_icc_get(&mas->se, NULL);
if (ret)
goto spi_geni_probe_runtime_disable;
/* Set the bus quota to a reasonable value for register access */
mas->se.icc_paths[GENI_TO_CORE].avg_bw = Bps_to_icc(CORE_2X_50_MHZ);
mas->se.icc_paths[CPU_TO_GENI].avg_bw = GENI_DEFAULT_BW;
ret = geni_icc_set_bw(&mas->se);
if (ret)
goto spi_geni_probe_runtime_disable;
ret = spi_geni_init(mas);
if (ret)
goto spi_geni_probe_runtime_disable;
/*
* check the mode supported and set_cs for fifo mode only
* for dma (gsi) mode, the gsi will set cs based on params passed in
* TRE
*/
if (!spi->target && mas->cur_xfer_mode == GENI_SE_FIFO)
spi->set_cs = spi_geni_set_cs;
/*
* TX is required per GSI spec, see setup_gsi_xfer().
*/
if (mas->cur_xfer_mode == GENI_GPI_DMA)
spi->flags = SPI_CONTROLLER_MUST_TX;
ret = request_irq(mas->irq, geni_spi_isr, 0, dev_name(dev), spi);
if (ret)
goto spi_geni_release_dma;
ret = spi_register_controller(spi);
if (ret)
goto spi_geni_probe_free_irq;
return 0;
spi_geni_probe_free_irq:
free_irq(mas->irq, spi);
spi_geni_release_dma:
spi_geni_release_dma_chan(mas);
spi_geni_probe_runtime_disable:
pm_runtime_disable(dev);
return ret;
}
static void spi_geni_remove(struct platform_device *pdev)
{
struct spi_controller *spi = platform_get_drvdata(pdev);
struct spi_geni_master *mas = spi_controller_get_devdata(spi);
/* Unregister _before_ disabling pm_runtime() so we stop transfers */
spi_unregister_controller(spi);
spi_geni_release_dma_chan(mas);
free_irq(mas->irq, spi);
pm_runtime_disable(&pdev->dev);
}
static int __maybe_unused spi_geni_runtime_suspend(struct device *dev)
{
struct spi_controller *spi = dev_get_drvdata(dev);
struct spi_geni_master *mas = spi_controller_get_devdata(spi);
int ret;
/* Drop the performance state vote */
dev_pm_opp_set_rate(dev, 0);
ret = geni_se_resources_off(&mas->se);
if (ret)
return ret;
return geni_icc_disable(&mas->se);
}
static int __maybe_unused spi_geni_runtime_resume(struct device *dev)
{
struct spi_controller *spi = dev_get_drvdata(dev);
struct spi_geni_master *mas = spi_controller_get_devdata(spi);
int ret;
ret = geni_icc_enable(&mas->se);
if (ret)
return ret;
ret = geni_se_resources_on(&mas->se);
if (ret)
return ret;
return dev_pm_opp_set_rate(mas->dev, mas->cur_sclk_hz);
}
static int __maybe_unused spi_geni_suspend(struct device *dev)
{
struct spi_controller *spi = dev_get_drvdata(dev);
int ret;
ret = spi_controller_suspend(spi);
if (ret)
return ret;
ret = pm_runtime_force_suspend(dev);
if (ret)
spi_controller_resume(spi);
return ret;
}
static int __maybe_unused spi_geni_resume(struct device *dev)
{
struct spi_controller *spi = dev_get_drvdata(dev);
int ret;
ret = pm_runtime_force_resume(dev);
if (ret)
return ret;
ret = spi_controller_resume(spi);
if (ret)
pm_runtime_force_suspend(dev);
return ret;
}
static const struct dev_pm_ops spi_geni_pm_ops = {
SET_RUNTIME_PM_OPS(spi_geni_runtime_suspend,
spi_geni_runtime_resume, NULL)
SET_SYSTEM_SLEEP_PM_OPS(spi_geni_suspend, spi_geni_resume)
};
static const struct of_device_id spi_geni_dt_match[] = {
{ .compatible = "qcom,geni-spi" },
{}
};
MODULE_DEVICE_TABLE(of, spi_geni_dt_match);
static struct platform_driver spi_geni_driver = {
.probe = spi_geni_probe,
.remove_new = spi_geni_remove,
.driver = {
.name = "geni_spi",
.pm = &spi_geni_pm_ops,
.of_match_table = spi_geni_dt_match,
},
};
module_platform_driver(spi_geni_driver);
MODULE_DESCRIPTION("SPI driver for GENI based QUP cores");
MODULE_LICENSE("GPL v2");