linux/drivers/iio/pressure/Kconfig

328 lines
8.9 KiB
Plaintext
Raw Normal View History

# SPDX-License-Identifier: GPL-2.0-only
#
# Pressure drivers
#
# When adding new entries keep the list in alphabetical order
menu "Pressure sensors"
config ABP060MG
tristate "Honeywell ABP pressure sensor driver"
depends on I2C
help
Say yes here to build support for the Honeywell ABP pressure
sensors.
To compile this driver as a module, choose M here: the module
will be called abp060mg.
iio: pressure: Support ROHM BU1390 Support for the ROHM BM1390 pressure sensor. The BM1390GLV-Z can measure pressures ranging from 300 hPa to 1300 hPa with configurable measurement averaging and internal FIFO. The sensor does also provide temperature measurements. Sensor does also contain IIR filter implemented in HW. The data-sheet says the IIR filter can be configured to be "weak", "middle" or "strong". Some RMS noise figures are provided in data sheet but no accurate maths for the filter configurations is provided. Hence, the IIR filter configuration is not supported by this driver and the filter is configured to the "middle" setting (at least not for now). The FIFO measurement mode is only measuring the pressure and not the temperature. The driver measures temperature when FIFO is flushed and simply uses the same measured temperature value to all reported temperatures. This should not be a problem when temperature is not changing very rapidly (several degrees C / second) but allows users to get the temperature measurements from sensor without any additional logic. This driver allows the sensor to be used in two muitually exclusive ways, 1. With trigger (data-ready IRQ). In this case the FIFO is not used as we get data ready for each collected sample. Instead, for each data-ready IRQ we read the sample from sensor and push it to the IIO buffer. 2. With hardware FIFO and watermark IRQ. In this case the data-ready is not used but we enable watermark IRQ. At each watermark IRQ we go and read all samples in FIFO and push them to the IIO buffer. Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Link: https://lore.kernel.org/r/4f23211e3cf248f9f48ddb2a752387bb00e9c2c4.1695727471.git.mazziesaccount@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2023-09-27 16:28:13 +08:00
config ROHM_BM1390
tristate "ROHM BM1390GLV-Z pressure sensor driver"
depends on I2C
help
Support for the ROHM BM1390 pressure sensor. The BM1390GLV-Z
can measure pressures ranging from 300 hPa to 1300 hPa with
configurable measurement averaging and internal FIFO. The
sensor does also provide temperature measurements.
config BMP280
tristate "Bosch Sensortec BMP180/BMP280/BMP380/BMP580 pressure sensor driver"
depends on (I2C || SPI_MASTER)
select REGMAP
select BMP280_I2C if (I2C)
select BMP280_SPI if (SPI_MASTER)
help
Say yes here to build support for Bosch Sensortec BMP180, BMP280, BMP380
and BMP580 pressure and temperature sensors. Also supports the BME280 with
an additional humidity sensor channel.
To compile this driver as a module, choose M here: the core module
will be called bmp280 and you will also get bmp280-i2c for I2C
and/or bmp280-spi for SPI support.
config BMP280_I2C
tristate
depends on BMP280
depends on I2C
select REGMAP_I2C
config BMP280_SPI
tristate
depends on BMP280
depends on SPI_MASTER
select REGMAP
config IIO_CROS_EC_BARO
tristate "ChromeOS EC Barometer Sensor"
depends on IIO_CROS_EC_SENSORS_CORE
help
Say yes here to build support for the Barometer sensor when
presented by the ChromeOS EC Sensor hub.
To compile this driver as a module, choose M here: the module
will be called cros_ec_baro.
config DLHL60D
tristate "All Sensors DLHL60D and DLHL60G low voltage digital pressure sensors"
depends on I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
Say yes here to build support for the All Sensors DLH series
pressure sensors driver.
To compile this driver as a module, choose M here: the module
will be called dlhl60d.
config DPS310
tristate "Infineon DPS310 pressure and temperature sensor"
depends on I2C
select REGMAP_I2C
help
Support for the Infineon DPS310 digital barometric pressure sensor.
It can be accessed over I2C bus.
This driver can also be built as a module. If so, the module will be
called dps310.
config HID_SENSOR_PRESS
depends on HID_SENSOR_HUB
select IIO_BUFFER
select HID_SENSOR_IIO_COMMON
select HID_SENSOR_IIO_TRIGGER
tristate "HID PRESS"
help
Say yes here to build support for the HID SENSOR
Pressure driver
To compile this driver as a module, choose M here: the module
will be called hid-sensor-press.
config HP03
tristate "Hope RF HP03 temperature and pressure sensor driver"
depends on I2C
select REGMAP_I2C
help
Say yes here to build support for Hope RF HP03 pressure and
temperature sensor.
To compile this driver as a module, choose M here: the module
will be called hp03.
config HSC030PA
tristate "Honeywell HSC/SSC TruStability pressure sensor series"
depends on (I2C || SPI_MASTER)
select HSC030PA_I2C if I2C
select HSC030PA_SPI if SPI_MASTER
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
Say Y here to build support for the Honeywell TruStability
HSC and SSC pressure and temperature sensor series.
To compile this driver as a module, choose M here: the module
will be called hsc030pa.
config HSC030PA_I2C
tristate
depends on HSC030PA
depends on I2C
config HSC030PA_SPI
tristate
depends on HSC030PA
depends on SPI_MASTER
config ICP10100
tristate "InvenSense ICP-101xx pressure and temperature sensor"
depends on I2C
select CRC8
help
Say yes here to build support for InvenSense ICP-101xx barometric
pressure and temperature sensor.
To compile this driver as a module, choose M here: the module
will be called icp10100.
config MPL115
tristate
config MPL115_I2C
tristate "Freescale MPL115A2 pressure sensor driver"
depends on I2C
select MPL115
help
Say yes here to build support for the Freescale MPL115A2
pressure sensor connected via I2C.
To compile this driver as a module, choose M here: the module
will be called mpl115_i2c.
config MPL115_SPI
tristate "Freescale MPL115A1 pressure sensor driver"
depends on SPI_MASTER
select MPL115
help
Say yes here to build support for the Freescale MPL115A1
pressure sensor connected via SPI.
To compile this driver as a module, choose M here: the module
will be called mpl115_spi.
config MPL3115
tristate "Freescale MPL3115A2 pressure sensor driver"
depends on I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
Say yes here to build support for the Freescale MPL3115A2
pressure sensor / altimeter.
To compile this driver as a module, choose M here: the module
will be called mpl3115.
config MPRLS0025PA
tristate "Honeywell MPRLS0025PA (MicroPressure sensors series)"
depends on (I2C || SPI_MASTER)
select MPRLS0025PA_I2C if I2C
select MPRLS0025PA_SPI if SPI_MASTER
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
Say Y here to build support for the Honeywell MicroPressure pressure
sensor series. There are many different types with different pressure
range. These ranges can be set up in the device tree.
To compile this driver as a module, choose M here: the module will be
called mprls0025pa.
config MPRLS0025PA_I2C
tristate
depends on MPRLS0025PA
depends on I2C
config MPRLS0025PA_SPI
tristate
depends on MPRLS0025PA
depends on SPI_MASTER
config MS5611
tristate "Measurement Specialties MS5611 pressure sensor driver"
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
Say Y here to build support for the Measurement Specialties
MS5611, MS5607 pressure and temperature sensors.
To compile this driver as a module, choose M here: the module will
be called ms5611_core.
config MS5611_I2C
tristate "support I2C bus connection"
depends on I2C && MS5611
help
Say Y here to build I2C bus support for MS5611.
To compile this driver as a module, choose M here: the module will
be called ms5611_i2c.
config MS5611_SPI
tristate "support SPI bus connection"
depends on SPI_MASTER && MS5611
help
Say Y here to build SPI bus support for MS5611.
To compile this driver as a module, choose M here: the module will
be called ms5611_spi.
config MS5637
tristate "Measurement Specialties MS5637 pressure & temperature sensor"
depends on I2C
select IIO_MS_SENSORS_I2C
help
If you say yes here you get support for the Measurement Specialties
MS5637 pressure and temperature sensor.
This driver is also used for MS8607 temperature, pressure & humidity
sensor
This driver can also be built as a module. If so, the module will
be called ms5637.
config IIO_ST_PRESS
tristate "STMicroelectronics pressure sensor Driver"
depends on (I2C || SPI_MASTER) && SYSFS
select IIO_ST_SENSORS_CORE
select IIO_TRIGGERED_BUFFER if (IIO_BUFFER)
help
Say yes here to build support for STMicroelectronics pressure
sensors: LPS001WP, LPS25H, LPS331AP, LPS22HB, LPS22HH.
Also need to enable at least one of I2C and SPI interface drivers
below.
config IIO_ST_PRESS_I2C
tristate "STMicroelectronics pressure sensor I2C Interface"
depends on I2C && IIO_ST_PRESS
default I2C && IIO_ST_PRESS
select IIO_ST_SENSORS_I2C
help
Build support for STMicroelectronics pressure sensor I2C interface.
To compile this driver as a module, choose M here. The module
will be called st_pressure_i2c.
config IIO_ST_PRESS_SPI
tristate "STMicroelectronics pressure sensor SPI Interface"
depends on SPI_MASTER && IIO_ST_PRESS
default SPI_MASTER && IIO_ST_PRESS
select IIO_ST_SENSORS_SPI
help
Build support for STMicroelectronics pressure sensor SPI interface.
To compile this driver as a module, choose M here. The module
will be called st_pressure_spi.
config T5403
tristate "EPCOS T5403 digital barometric pressure sensor driver"
depends on I2C
help
Say yes here to build support for the EPCOS T5403 pressure sensor
connected via I2C.
To compile this driver as a module, choose M here: the module
will be called t5403.
config HP206C
tristate "HOPERF HP206C precision barometer and altimeter sensor"
depends on I2C
help
Say yes here to build support for the HOPREF HP206C precision
barometer and altimeter sensor.
This driver can also be built as a module. If so, the module will
be called hp206c.
config ZPA2326
tristate "Murata ZPA2326 pressure sensor driver"
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
select REGMAP
select ZPA2326_I2C if I2C
select ZPA2326_SPI if SPI_MASTER
help
Say Y here to build support for the Murata ZPA2326 pressure and
temperature sensor.
To compile this driver as a module, choose M here: the module will
be called zpa2326.
config ZPA2326_I2C
tristate
select REGMAP_I2C
config ZPA2326_SPI
tristate
select REGMAP_SPI
endmenu