linux/arch/riscv/mm/init.c

883 lines
25 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2012 Regents of the University of California
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
* Copyright (C) 2019 Western Digital Corporation or its affiliates.
* Copyright (C) 2020 FORTH-ICS/CARV
* Nick Kossifidis <mick@ics.forth.gr>
*/
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/memblock.h>
mm: remove include/linux/bootmem.h Move remaining definitions and declarations from include/linux/bootmem.h into include/linux/memblock.h and remove the redundant header. The includes were replaced with the semantic patch below and then semi-automated removal of duplicated '#include <linux/memblock.h> @@ @@ - #include <linux/bootmem.h> + #include <linux/memblock.h> [sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h] Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au [sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h] Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au [sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal] Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Ingo Molnar <mingo@redhat.com> Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Jonas Bonn <jonas@southpole.se> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Ley Foon Tan <lftan@altera.com> Cc: Mark Salter <msalter@redhat.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Matt Turner <mattst88@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Palmer Dabbelt <palmer@sifive.com> Cc: Paul Burton <paul.burton@mips.com> Cc: Richard Kuo <rkuo@codeaurora.org> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Serge Semin <fancer.lancer@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-10-31 06:09:49 +08:00
#include <linux/initrd.h>
#include <linux/swap.h>
#include <linux/sizes.h>
#include <linux/of_fdt.h>
#include <linux/of_reserved_mem.h>
riscv: Fix memblock reservation for device tree blob This fixes an error with how the FDT blob is reserved in memblock. An incorrect physical address calculation exposed the FDT header to unintended corruption, which typically manifested with of_fdt_raw_init() faulting during late boot after fdt_totalsize() returned a wrong value. Systems with smaller physical memory sizes more frequently trigger this issue, as the kernel is more likely to allocate from the DMA32 zone where bbl places the DTB after the kernel image. Commit 671f9a3e2e24 ("RISC-V: Setup initial page tables in two stages") changed the mapping of the DTB to reside in the fixmap area. Consequently, early_init_fdt_reserve_self() cannot be used anymore in setup_bootmem() since it relies on __pa() to derive a physical address, which does not work with dtb_early_va that is no longer a valid kernel logical address. The reserved[0x1] region shows the effect of the pointer underflow resulting from the __pa(initial_boot_params) offset subtraction: [ 0.000000] MEMBLOCK configuration: [ 0.000000] memory size = 0x000000001fe00000 reserved size = 0x0000000000a2e514 [ 0.000000] memory.cnt = 0x1 [ 0.000000] memory[0x0] [0x0000000080200000-0x000000009fffffff], 0x000000001fe00000 bytes flags: 0x0 [ 0.000000] reserved.cnt = 0x2 [ 0.000000] reserved[0x0] [0x0000000080200000-0x0000000080c2dfeb], 0x0000000000a2dfec bytes flags: 0x0 [ 0.000000] reserved[0x1] [0xfffffff080100000-0xfffffff080100527], 0x0000000000000528 bytes flags: 0x0 With the fix applied: [ 0.000000] MEMBLOCK configuration: [ 0.000000] memory size = 0x000000001fe00000 reserved size = 0x0000000000a2e514 [ 0.000000] memory.cnt = 0x1 [ 0.000000] memory[0x0] [0x0000000080200000-0x000000009fffffff], 0x000000001fe00000 bytes flags: 0x0 [ 0.000000] reserved.cnt = 0x2 [ 0.000000] reserved[0x0] [0x0000000080200000-0x0000000080c2dfeb], 0x0000000000a2dfec bytes flags: 0x0 [ 0.000000] reserved[0x1] [0x0000000080e00000-0x0000000080e00527], 0x0000000000000528 bytes flags: 0x0 Fixes: 671f9a3e2e24 ("RISC-V: Setup initial page tables in two stages") Signed-off-by: Albert Ou <aou@eecs.berkeley.edu> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-09-28 07:14:18 +08:00
#include <linux/libfdt.h>
#include <linux/set_memory.h>
#include <linux/dma-map-ops.h>
#include <linux/crash_dump.h>
#include <asm/fixmap.h>
#include <asm/tlbflush.h>
#include <asm/sections.h>
#include <asm/soc.h>
#include <asm/io.h>
#include <asm/ptdump.h>
#include <asm/numa.h>
#include "../kernel/head.h"
unsigned long kernel_virt_addr = KERNEL_LINK_ADDR;
EXPORT_SYMBOL(kernel_virt_addr);
#ifdef CONFIG_XIP_KERNEL
#define kernel_virt_addr (*((unsigned long *)XIP_FIXUP(&kernel_virt_addr)))
extern char _xiprom[], _exiprom[];
#endif
unsigned long empty_zero_page[PAGE_SIZE / sizeof(unsigned long)]
__page_aligned_bss;
EXPORT_SYMBOL(empty_zero_page);
extern char _start[];
#define DTB_EARLY_BASE_VA PGDIR_SIZE
void *_dtb_early_va __initdata;
uintptr_t _dtb_early_pa __initdata;
struct pt_alloc_ops {
pte_t *(*get_pte_virt)(phys_addr_t pa);
phys_addr_t (*alloc_pte)(uintptr_t va);
#ifndef __PAGETABLE_PMD_FOLDED
pmd_t *(*get_pmd_virt)(phys_addr_t pa);
phys_addr_t (*alloc_pmd)(uintptr_t va);
#endif
};
static phys_addr_t dma32_phys_limit __initdata;
static void __init zone_sizes_init(void)
{
unsigned long max_zone_pfns[MAX_NR_ZONES] = { 0, };
#ifdef CONFIG_ZONE_DMA32
max_zone_pfns[ZONE_DMA32] = PFN_DOWN(dma32_phys_limit);
#endif
max_zone_pfns[ZONE_NORMAL] = max_low_pfn;
mm: use free_area_init() instead of free_area_init_nodes() free_area_init() has effectively became a wrapper for free_area_init_nodes() and there is no point of keeping it. Still free_area_init() name is shorter and more general as it does not imply necessity to initialize multiple nodes. Rename free_area_init_nodes() to free_area_init(), update the callers and drop old version of free_area_init(). Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Tested-by: Hoan Tran <hoan@os.amperecomputing.com> [arm64] Reviewed-by: Baoquan He <bhe@redhat.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Brian Cain <bcain@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Hocko <mhocko@kernel.org> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200412194859.12663-6-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-04 06:57:10 +08:00
free_area_init(max_zone_pfns);
}
#if defined(CONFIG_MMU) && defined(CONFIG_DEBUG_VM)
static inline void print_mlk(char *name, unsigned long b, unsigned long t)
{
pr_notice("%12s : 0x%08lx - 0x%08lx (%4ld kB)\n", name, b, t,
(((t) - (b)) >> 10));
}
static inline void print_mlm(char *name, unsigned long b, unsigned long t)
{
pr_notice("%12s : 0x%08lx - 0x%08lx (%4ld MB)\n", name, b, t,
(((t) - (b)) >> 20));
}
static void __init print_vm_layout(void)
{
pr_notice("Virtual kernel memory layout:\n");
print_mlk("fixmap", (unsigned long)FIXADDR_START,
(unsigned long)FIXADDR_TOP);
print_mlm("pci io", (unsigned long)PCI_IO_START,
(unsigned long)PCI_IO_END);
print_mlm("vmemmap", (unsigned long)VMEMMAP_START,
(unsigned long)VMEMMAP_END);
print_mlm("vmalloc", (unsigned long)VMALLOC_START,
(unsigned long)VMALLOC_END);
print_mlm("lowmem", (unsigned long)PAGE_OFFSET,
(unsigned long)high_memory);
#ifdef CONFIG_64BIT
print_mlm("kernel", (unsigned long)KERNEL_LINK_ADDR,
(unsigned long)ADDRESS_SPACE_END);
#endif
}
#else
static void print_vm_layout(void) { }
#endif /* CONFIG_DEBUG_VM */
void __init mem_init(void)
{
#ifdef CONFIG_FLATMEM
BUG_ON(!mem_map);
#endif /* CONFIG_FLATMEM */
high_memory = (void *)(__va(PFN_PHYS(max_low_pfn)));
memblock: rename free_all_bootmem to memblock_free_all The conversion is done using sed -i 's@free_all_bootmem@memblock_free_all@' \ $(git grep -l free_all_bootmem) Link: http://lkml.kernel.org/r/1536927045-23536-26-git-send-email-rppt@linux.vnet.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Ingo Molnar <mingo@redhat.com> Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Jonas Bonn <jonas@southpole.se> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Ley Foon Tan <lftan@altera.com> Cc: Mark Salter <msalter@redhat.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Matt Turner <mattst88@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Palmer Dabbelt <palmer@sifive.com> Cc: Paul Burton <paul.burton@mips.com> Cc: Richard Kuo <rkuo@codeaurora.org> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Serge Semin <fancer.lancer@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-10-31 06:09:30 +08:00
memblock_free_all();
print_vm_layout();
}
static void __init setup_bootmem(void)
{
phys_addr_t vmlinux_end = __pa_symbol(&_end);
phys_addr_t vmlinux_start = __pa_symbol(&_start);
phys_addr_t dram_end = memblock_end_of_DRAM();
phys_addr_t max_mapped_addr = __pa(~(ulong)0);
#ifdef CONFIG_XIP_KERNEL
vmlinux_start = __pa_symbol(&_sdata);
#endif
/* The maximal physical memory size is -PAGE_OFFSET. */
memblock_enforce_memory_limit(-PAGE_OFFSET);
/*
* Reserve from the start of the kernel to the end of the kernel
*/
#if defined(CONFIG_64BIT) && defined(CONFIG_STRICT_KERNEL_RWX)
/*
* Make sure we align the reservation on PMD_SIZE since we will
* map the kernel in the linear mapping as read-only: we do not want
* any allocation to happen between _end and the next pmd aligned page.
*/
vmlinux_end = (vmlinux_end + PMD_SIZE - 1) & PMD_MASK;
#endif
memblock_reserve(vmlinux_start, vmlinux_end - vmlinux_start);
/*
* memblock allocator is not aware of the fact that last 4K bytes of
* the addressable memory can not be mapped because of IS_ERR_VALUE
* macro. Make sure that last 4k bytes are not usable by memblock
* if end of dram is equal to maximum addressable memory.
*/
if (max_mapped_addr == (dram_end - 1))
memblock_set_current_limit(max_mapped_addr - 4096);
min_low_pfn = PFN_UP(memblock_start_of_DRAM());
max_low_pfn = max_pfn = PFN_DOWN(dram_end);
dma32_phys_limit = min(4UL * SZ_1G, (unsigned long)PFN_PHYS(max_low_pfn));
set_max_mapnr(max_low_pfn - ARCH_PFN_OFFSET);
reserve_initrd_mem();
riscv: Fix memblock reservation for device tree blob This fixes an error with how the FDT blob is reserved in memblock. An incorrect physical address calculation exposed the FDT header to unintended corruption, which typically manifested with of_fdt_raw_init() faulting during late boot after fdt_totalsize() returned a wrong value. Systems with smaller physical memory sizes more frequently trigger this issue, as the kernel is more likely to allocate from the DMA32 zone where bbl places the DTB after the kernel image. Commit 671f9a3e2e24 ("RISC-V: Setup initial page tables in two stages") changed the mapping of the DTB to reside in the fixmap area. Consequently, early_init_fdt_reserve_self() cannot be used anymore in setup_bootmem() since it relies on __pa() to derive a physical address, which does not work with dtb_early_va that is no longer a valid kernel logical address. The reserved[0x1] region shows the effect of the pointer underflow resulting from the __pa(initial_boot_params) offset subtraction: [ 0.000000] MEMBLOCK configuration: [ 0.000000] memory size = 0x000000001fe00000 reserved size = 0x0000000000a2e514 [ 0.000000] memory.cnt = 0x1 [ 0.000000] memory[0x0] [0x0000000080200000-0x000000009fffffff], 0x000000001fe00000 bytes flags: 0x0 [ 0.000000] reserved.cnt = 0x2 [ 0.000000] reserved[0x0] [0x0000000080200000-0x0000000080c2dfeb], 0x0000000000a2dfec bytes flags: 0x0 [ 0.000000] reserved[0x1] [0xfffffff080100000-0xfffffff080100527], 0x0000000000000528 bytes flags: 0x0 With the fix applied: [ 0.000000] MEMBLOCK configuration: [ 0.000000] memory size = 0x000000001fe00000 reserved size = 0x0000000000a2e514 [ 0.000000] memory.cnt = 0x1 [ 0.000000] memory[0x0] [0x0000000080200000-0x000000009fffffff], 0x000000001fe00000 bytes flags: 0x0 [ 0.000000] reserved.cnt = 0x2 [ 0.000000] reserved[0x0] [0x0000000080200000-0x0000000080c2dfeb], 0x0000000000a2dfec bytes flags: 0x0 [ 0.000000] reserved[0x1] [0x0000000080e00000-0x0000000080e00527], 0x0000000000000528 bytes flags: 0x0 Fixes: 671f9a3e2e24 ("RISC-V: Setup initial page tables in two stages") Signed-off-by: Albert Ou <aou@eecs.berkeley.edu> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-09-28 07:14:18 +08:00
/*
* If DTB is built in, no need to reserve its memblock.
* Otherwise, do reserve it but avoid using
* early_init_fdt_reserve_self() since __pa() does
riscv: Fix memblock reservation for device tree blob This fixes an error with how the FDT blob is reserved in memblock. An incorrect physical address calculation exposed the FDT header to unintended corruption, which typically manifested with of_fdt_raw_init() faulting during late boot after fdt_totalsize() returned a wrong value. Systems with smaller physical memory sizes more frequently trigger this issue, as the kernel is more likely to allocate from the DMA32 zone where bbl places the DTB after the kernel image. Commit 671f9a3e2e24 ("RISC-V: Setup initial page tables in two stages") changed the mapping of the DTB to reside in the fixmap area. Consequently, early_init_fdt_reserve_self() cannot be used anymore in setup_bootmem() since it relies on __pa() to derive a physical address, which does not work with dtb_early_va that is no longer a valid kernel logical address. The reserved[0x1] region shows the effect of the pointer underflow resulting from the __pa(initial_boot_params) offset subtraction: [ 0.000000] MEMBLOCK configuration: [ 0.000000] memory size = 0x000000001fe00000 reserved size = 0x0000000000a2e514 [ 0.000000] memory.cnt = 0x1 [ 0.000000] memory[0x0] [0x0000000080200000-0x000000009fffffff], 0x000000001fe00000 bytes flags: 0x0 [ 0.000000] reserved.cnt = 0x2 [ 0.000000] reserved[0x0] [0x0000000080200000-0x0000000080c2dfeb], 0x0000000000a2dfec bytes flags: 0x0 [ 0.000000] reserved[0x1] [0xfffffff080100000-0xfffffff080100527], 0x0000000000000528 bytes flags: 0x0 With the fix applied: [ 0.000000] MEMBLOCK configuration: [ 0.000000] memory size = 0x000000001fe00000 reserved size = 0x0000000000a2e514 [ 0.000000] memory.cnt = 0x1 [ 0.000000] memory[0x0] [0x0000000080200000-0x000000009fffffff], 0x000000001fe00000 bytes flags: 0x0 [ 0.000000] reserved.cnt = 0x2 [ 0.000000] reserved[0x0] [0x0000000080200000-0x0000000080c2dfeb], 0x0000000000a2dfec bytes flags: 0x0 [ 0.000000] reserved[0x1] [0x0000000080e00000-0x0000000080e00527], 0x0000000000000528 bytes flags: 0x0 Fixes: 671f9a3e2e24 ("RISC-V: Setup initial page tables in two stages") Signed-off-by: Albert Ou <aou@eecs.berkeley.edu> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-09-28 07:14:18 +08:00
* not work for DTB pointers that are fixmap addresses
*/
if (!IS_ENABLED(CONFIG_BUILTIN_DTB))
memblock_reserve(dtb_early_pa, fdt_totalsize(dtb_early_va));
riscv: Fix memblock reservation for device tree blob This fixes an error with how the FDT blob is reserved in memblock. An incorrect physical address calculation exposed the FDT header to unintended corruption, which typically manifested with of_fdt_raw_init() faulting during late boot after fdt_totalsize() returned a wrong value. Systems with smaller physical memory sizes more frequently trigger this issue, as the kernel is more likely to allocate from the DMA32 zone where bbl places the DTB after the kernel image. Commit 671f9a3e2e24 ("RISC-V: Setup initial page tables in two stages") changed the mapping of the DTB to reside in the fixmap area. Consequently, early_init_fdt_reserve_self() cannot be used anymore in setup_bootmem() since it relies on __pa() to derive a physical address, which does not work with dtb_early_va that is no longer a valid kernel logical address. The reserved[0x1] region shows the effect of the pointer underflow resulting from the __pa(initial_boot_params) offset subtraction: [ 0.000000] MEMBLOCK configuration: [ 0.000000] memory size = 0x000000001fe00000 reserved size = 0x0000000000a2e514 [ 0.000000] memory.cnt = 0x1 [ 0.000000] memory[0x0] [0x0000000080200000-0x000000009fffffff], 0x000000001fe00000 bytes flags: 0x0 [ 0.000000] reserved.cnt = 0x2 [ 0.000000] reserved[0x0] [0x0000000080200000-0x0000000080c2dfeb], 0x0000000000a2dfec bytes flags: 0x0 [ 0.000000] reserved[0x1] [0xfffffff080100000-0xfffffff080100527], 0x0000000000000528 bytes flags: 0x0 With the fix applied: [ 0.000000] MEMBLOCK configuration: [ 0.000000] memory size = 0x000000001fe00000 reserved size = 0x0000000000a2e514 [ 0.000000] memory.cnt = 0x1 [ 0.000000] memory[0x0] [0x0000000080200000-0x000000009fffffff], 0x000000001fe00000 bytes flags: 0x0 [ 0.000000] reserved.cnt = 0x2 [ 0.000000] reserved[0x0] [0x0000000080200000-0x0000000080c2dfeb], 0x0000000000a2dfec bytes flags: 0x0 [ 0.000000] reserved[0x1] [0x0000000080e00000-0x0000000080e00527], 0x0000000000000528 bytes flags: 0x0 Fixes: 671f9a3e2e24 ("RISC-V: Setup initial page tables in two stages") Signed-off-by: Albert Ou <aou@eecs.berkeley.edu> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-09-28 07:14:18 +08:00
early_init_fdt_scan_reserved_mem();
dma_contiguous_reserve(dma32_phys_limit);
memblock_allow_resize();
}
#ifdef CONFIG_MMU
static struct pt_alloc_ops _pt_ops __initdata;
#ifdef CONFIG_XIP_KERNEL
#define pt_ops (*(struct pt_alloc_ops *)XIP_FIXUP(&_pt_ops))
#else
#define pt_ops _pt_ops
#endif
/* Offset between linear mapping virtual address and kernel load address */
unsigned long va_pa_offset __ro_after_init;
EXPORT_SYMBOL(va_pa_offset);
#ifdef CONFIG_XIP_KERNEL
#define va_pa_offset (*((unsigned long *)XIP_FIXUP(&va_pa_offset)))
#endif
/* Offset between kernel mapping virtual address and kernel load address */
#ifdef CONFIG_64BIT
unsigned long va_kernel_pa_offset __ro_after_init;
EXPORT_SYMBOL(va_kernel_pa_offset);
#endif
#ifdef CONFIG_XIP_KERNEL
#define va_kernel_pa_offset (*((unsigned long *)XIP_FIXUP(&va_kernel_pa_offset)))
#endif
unsigned long va_kernel_xip_pa_offset __ro_after_init;
EXPORT_SYMBOL(va_kernel_xip_pa_offset);
#ifdef CONFIG_XIP_KERNEL
#define va_kernel_xip_pa_offset (*((unsigned long *)XIP_FIXUP(&va_kernel_xip_pa_offset)))
#endif
unsigned long pfn_base __ro_after_init;
EXPORT_SYMBOL(pfn_base);
pgd_t swapper_pg_dir[PTRS_PER_PGD] __page_aligned_bss;
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
pgd_t trampoline_pg_dir[PTRS_PER_PGD] __page_aligned_bss;
static pte_t fixmap_pte[PTRS_PER_PTE] __page_aligned_bss;
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
pgd_t early_pg_dir[PTRS_PER_PGD] __initdata __aligned(PAGE_SIZE);
#ifdef CONFIG_XIP_KERNEL
#define trampoline_pg_dir ((pgd_t *)XIP_FIXUP(trampoline_pg_dir))
#define fixmap_pte ((pte_t *)XIP_FIXUP(fixmap_pte))
#define early_pg_dir ((pgd_t *)XIP_FIXUP(early_pg_dir))
#endif /* CONFIG_XIP_KERNEL */
void __set_fixmap(enum fixed_addresses idx, phys_addr_t phys, pgprot_t prot)
{
unsigned long addr = __fix_to_virt(idx);
pte_t *ptep;
BUG_ON(idx <= FIX_HOLE || idx >= __end_of_fixed_addresses);
ptep = &fixmap_pte[pte_index(addr)];
if (pgprot_val(prot))
set_pte(ptep, pfn_pte(phys >> PAGE_SHIFT, prot));
else
pte_clear(&init_mm, addr, ptep);
local_flush_tlb_page(addr);
}
static inline pte_t *__init get_pte_virt_early(phys_addr_t pa)
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
{
return (pte_t *)((uintptr_t)pa);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
}
static inline pte_t *__init get_pte_virt_fixmap(phys_addr_t pa)
{
clear_fixmap(FIX_PTE);
return (pte_t *)set_fixmap_offset(FIX_PTE, pa);
}
static inline pte_t *__init get_pte_virt_late(phys_addr_t pa)
{
return (pte_t *) __va(pa);
}
static inline phys_addr_t __init alloc_pte_early(uintptr_t va)
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
{
/*
* We only create PMD or PGD early mappings so we
* should never reach here with MMU disabled.
*/
BUG();
}
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
static inline phys_addr_t __init alloc_pte_fixmap(uintptr_t va)
{
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
return memblock_phys_alloc(PAGE_SIZE, PAGE_SIZE);
}
static phys_addr_t __init alloc_pte_late(uintptr_t va)
{
unsigned long vaddr;
vaddr = __get_free_page(GFP_KERNEL);
BUG_ON(!vaddr || !pgtable_pte_page_ctor(virt_to_page(vaddr)));
return __pa(vaddr);
}
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
static void __init create_pte_mapping(pte_t *ptep,
uintptr_t va, phys_addr_t pa,
phys_addr_t sz, pgprot_t prot)
{
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
uintptr_t pte_idx = pte_index(va);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
BUG_ON(sz != PAGE_SIZE);
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
if (pte_none(ptep[pte_idx]))
ptep[pte_idx] = pfn_pte(PFN_DOWN(pa), prot);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
}
#ifndef __PAGETABLE_PMD_FOLDED
static pmd_t trampoline_pmd[PTRS_PER_PMD] __page_aligned_bss;
static pmd_t fixmap_pmd[PTRS_PER_PMD] __page_aligned_bss;
static pmd_t early_pmd[PTRS_PER_PMD] __initdata __aligned(PAGE_SIZE);
static pmd_t early_dtb_pmd[PTRS_PER_PMD] __initdata __aligned(PAGE_SIZE);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
#ifdef CONFIG_XIP_KERNEL
#define trampoline_pmd ((pmd_t *)XIP_FIXUP(trampoline_pmd))
#define fixmap_pmd ((pmd_t *)XIP_FIXUP(fixmap_pmd))
#define early_pmd ((pmd_t *)XIP_FIXUP(early_pmd))
#endif /* CONFIG_XIP_KERNEL */
static pmd_t *__init get_pmd_virt_early(phys_addr_t pa)
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
{
/* Before MMU is enabled */
return (pmd_t *)((uintptr_t)pa);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
}
static pmd_t *__init get_pmd_virt_fixmap(phys_addr_t pa)
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
{
clear_fixmap(FIX_PMD);
return (pmd_t *)set_fixmap_offset(FIX_PMD, pa);
}
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
static pmd_t *__init get_pmd_virt_late(phys_addr_t pa)
{
return (pmd_t *) __va(pa);
}
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
static phys_addr_t __init alloc_pmd_early(uintptr_t va)
{
BUG_ON((va - kernel_virt_addr) >> PGDIR_SHIFT);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
return (uintptr_t)early_pmd;
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
}
static phys_addr_t __init alloc_pmd_fixmap(uintptr_t va)
{
return memblock_phys_alloc(PAGE_SIZE, PAGE_SIZE);
}
static phys_addr_t __init alloc_pmd_late(uintptr_t va)
{
unsigned long vaddr;
vaddr = __get_free_page(GFP_KERNEL);
BUG_ON(!vaddr);
return __pa(vaddr);
}
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
static void __init create_pmd_mapping(pmd_t *pmdp,
uintptr_t va, phys_addr_t pa,
phys_addr_t sz, pgprot_t prot)
{
pte_t *ptep;
phys_addr_t pte_phys;
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
uintptr_t pmd_idx = pmd_index(va);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
if (sz == PMD_SIZE) {
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
if (pmd_none(pmdp[pmd_idx]))
pmdp[pmd_idx] = pfn_pmd(PFN_DOWN(pa), prot);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
return;
}
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
if (pmd_none(pmdp[pmd_idx])) {
pte_phys = pt_ops.alloc_pte(va);
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
pmdp[pmd_idx] = pfn_pmd(PFN_DOWN(pte_phys), PAGE_TABLE);
ptep = pt_ops.get_pte_virt(pte_phys);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
memset(ptep, 0, PAGE_SIZE);
} else {
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
pte_phys = PFN_PHYS(_pmd_pfn(pmdp[pmd_idx]));
ptep = pt_ops.get_pte_virt(pte_phys);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
}
create_pte_mapping(ptep, va, pa, sz, prot);
}
#define pgd_next_t pmd_t
#define alloc_pgd_next(__va) pt_ops.alloc_pmd(__va)
#define get_pgd_next_virt(__pa) pt_ops.get_pmd_virt(__pa)
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
#define create_pgd_next_mapping(__nextp, __va, __pa, __sz, __prot) \
create_pmd_mapping(__nextp, __va, __pa, __sz, __prot)
#define fixmap_pgd_next fixmap_pmd
#else
#define pgd_next_t pte_t
#define alloc_pgd_next(__va) pt_ops.alloc_pte(__va)
#define get_pgd_next_virt(__pa) pt_ops.get_pte_virt(__pa)
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
#define create_pgd_next_mapping(__nextp, __va, __pa, __sz, __prot) \
create_pte_mapping(__nextp, __va, __pa, __sz, __prot)
#define fixmap_pgd_next fixmap_pte
#endif
void __init create_pgd_mapping(pgd_t *pgdp,
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
uintptr_t va, phys_addr_t pa,
phys_addr_t sz, pgprot_t prot)
{
pgd_next_t *nextp;
phys_addr_t next_phys;
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
uintptr_t pgd_idx = pgd_index(va);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
if (sz == PGDIR_SIZE) {
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
if (pgd_val(pgdp[pgd_idx]) == 0)
pgdp[pgd_idx] = pfn_pgd(PFN_DOWN(pa), prot);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
return;
}
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
if (pgd_val(pgdp[pgd_idx]) == 0) {
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
next_phys = alloc_pgd_next(va);
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
pgdp[pgd_idx] = pfn_pgd(PFN_DOWN(next_phys), PAGE_TABLE);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
nextp = get_pgd_next_virt(next_phys);
memset(nextp, 0, PAGE_SIZE);
} else {
mm: consolidate pte_index() and pte_offset_*() definitions All architectures define pte_index() as (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1) and all architectures define pte_offset_kernel() as an entry in the array of PTEs indexed by the pte_index(). For the most architectures the pte_offset_kernel() implementation relies on the availability of pmd_page_vaddr() that converts a PMD entry value to the virtual address of the page containing PTEs array. Let's move x86 definitions of the PTE accessors to the generic place in <linux/pgtable.h> and then simply drop the respective definitions from the other architectures. The architectures that didn't provide pmd_page_vaddr() are updated to have that defined. The generic implementation of pte_offset_kernel() can be overridden by an architecture and alpha makes use of this because it has special ordering requirements for its version of pte_offset_kernel(). [rppt@linux.ibm.com: v2] Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org [rppt@linux.ibm.com: update] Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org [akpm@linux-foundation.org: fix x86 warning] [sfr@canb.auug.org.au: fix powerpc build] Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Cain <bcain@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Guo Ren <guoren@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Mark Salter <msalter@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Nick Hu <nickhu@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 12:33:10 +08:00
next_phys = PFN_PHYS(_pgd_pfn(pgdp[pgd_idx]));
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
nextp = get_pgd_next_virt(next_phys);
}
create_pgd_next_mapping(nextp, va, pa, sz, prot);
}
static uintptr_t __init best_map_size(phys_addr_t base, phys_addr_t size)
{
/* Upgrade to PMD_SIZE mappings whenever possible */
if ((base & (PMD_SIZE - 1)) || (size & (PMD_SIZE - 1)))
return PAGE_SIZE;
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
return PMD_SIZE;
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
}
#ifdef CONFIG_XIP_KERNEL
/* called from head.S with MMU off */
asmlinkage void __init __copy_data(void)
{
void *from = (void *)(&_sdata);
void *end = (void *)(&_end);
void *to = (void *)CONFIG_PHYS_RAM_BASE;
size_t sz = (size_t)(end - from + 1);
memcpy(to, from, sz);
}
#endif
/*
* setup_vm() is called from head.S with MMU-off.
*
* Following requirements should be honoured for setup_vm() to work
* correctly:
* 1) It should use PC-relative addressing for accessing kernel symbols.
* To achieve this we always use GCC cmodel=medany.
* 2) The compiler instrumentation for FTRACE will not work for setup_vm()
* so disable compiler instrumentation when FTRACE is enabled.
*
* Currently, the above requirements are honoured by using custom CFLAGS
* for init.o in mm/Makefile.
*/
#ifndef __riscv_cmodel_medany
#error "setup_vm() is called from head.S before relocate so it should not use absolute addressing."
#endif
static uintptr_t load_pa __initdata;
static uintptr_t load_sz __initdata;
#ifdef CONFIG_XIP_KERNEL
#define load_pa (*((uintptr_t *)XIP_FIXUP(&load_pa)))
#define load_sz (*((uintptr_t *)XIP_FIXUP(&load_sz)))
#endif
#ifdef CONFIG_XIP_KERNEL
static uintptr_t xiprom __inidata;
static uintptr_t xiprom_sz __initdata;
#define xiprom_sz (*((uintptr_t *)XIP_FIXUP(&xiprom_sz)))
#define xiprom (*((uintptr_t *)XIP_FIXUP(&xiprom)))
static void __init create_kernel_page_table(pgd_t *pgdir, uintptr_t map_size)
{
uintptr_t va, end_va;
/* Map the flash resident part */
end_va = kernel_virt_addr + xiprom_sz;
for (va = kernel_virt_addr; va < end_va; va += map_size)
create_pgd_mapping(pgdir, va,
xiprom + (va - kernel_virt_addr),
map_size, PAGE_KERNEL_EXEC);
/* Map the data in RAM */
end_va = kernel_virt_addr + XIP_OFFSET + load_sz;
for (va = kernel_virt_addr + XIP_OFFSET; va < end_va; va += map_size)
create_pgd_mapping(pgdir, va,
load_pa + (va - (kernel_virt_addr + XIP_OFFSET)),
map_size, PAGE_KERNEL);
}
#else
static void __init create_kernel_page_table(pgd_t *pgdir, uintptr_t map_size)
{
uintptr_t va, end_va;
end_va = kernel_virt_addr + load_sz;
for (va = kernel_virt_addr; va < end_va; va += map_size)
create_pgd_mapping(pgdir, va,
load_pa + (va - kernel_virt_addr),
map_size, PAGE_KERNEL_EXEC);
}
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
asmlinkage void __init setup_vm(uintptr_t dtb_pa)
{
uintptr_t __maybe_unused pa;
uintptr_t map_size;
#ifndef __PAGETABLE_PMD_FOLDED
pmd_t fix_bmap_spmd, fix_bmap_epmd;
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
#ifdef CONFIG_XIP_KERNEL
xiprom = (uintptr_t)CONFIG_XIP_PHYS_ADDR;
xiprom_sz = (uintptr_t)(&_exiprom) - (uintptr_t)(&_xiprom);
load_pa = (uintptr_t)CONFIG_PHYS_RAM_BASE;
load_sz = (uintptr_t)(&_end) - (uintptr_t)(&_sdata);
va_kernel_xip_pa_offset = kernel_virt_addr - xiprom;
#else
load_pa = (uintptr_t)(&_start);
load_sz = (uintptr_t)(&_end) - load_pa;
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
va_pa_offset = PAGE_OFFSET - load_pa;
#ifdef CONFIG_64BIT
va_kernel_pa_offset = kernel_virt_addr - load_pa;
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
pfn_base = PFN_DOWN(load_pa);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
/*
* Enforce boot alignment requirements of RV32 and
* RV64 by only allowing PMD or PGD mappings.
*/
map_size = PMD_SIZE;
/* Sanity check alignment and size */
BUG_ON((PAGE_OFFSET % PGDIR_SIZE) != 0);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
BUG_ON((load_pa % map_size) != 0);
pt_ops.alloc_pte = alloc_pte_early;
pt_ops.get_pte_virt = get_pte_virt_early;
#ifndef __PAGETABLE_PMD_FOLDED
pt_ops.alloc_pmd = alloc_pmd_early;
pt_ops.get_pmd_virt = get_pmd_virt_early;
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
/* Setup early PGD for fixmap */
create_pgd_mapping(early_pg_dir, FIXADDR_START,
(uintptr_t)fixmap_pgd_next, PGDIR_SIZE, PAGE_TABLE);
#ifndef __PAGETABLE_PMD_FOLDED
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
/* Setup fixmap PMD */
create_pmd_mapping(fixmap_pmd, FIXADDR_START,
(uintptr_t)fixmap_pte, PMD_SIZE, PAGE_TABLE);
/* Setup trampoline PGD and PMD */
create_pgd_mapping(trampoline_pg_dir, kernel_virt_addr,
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
(uintptr_t)trampoline_pmd, PGDIR_SIZE, PAGE_TABLE);
#ifdef CONFIG_XIP_KERNEL
create_pmd_mapping(trampoline_pmd, kernel_virt_addr,
xiprom, PMD_SIZE, PAGE_KERNEL_EXEC);
#else
create_pmd_mapping(trampoline_pmd, kernel_virt_addr,
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
load_pa, PMD_SIZE, PAGE_KERNEL_EXEC);
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
#else
/* Setup trampoline PGD */
create_pgd_mapping(trampoline_pg_dir, kernel_virt_addr,
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
load_pa, PGDIR_SIZE, PAGE_KERNEL_EXEC);
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
/*
* Setup early PGD covering entire kernel which will allow
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
* us to reach paging_init(). We map all memory banks later
* in setup_vm_final() below.
*/
create_kernel_page_table(early_pg_dir, map_size);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
#ifndef __PAGETABLE_PMD_FOLDED
/* Setup early PMD for DTB */
create_pgd_mapping(early_pg_dir, DTB_EARLY_BASE_VA,
(uintptr_t)early_dtb_pmd, PGDIR_SIZE, PAGE_TABLE);
#ifndef CONFIG_BUILTIN_DTB
/* Create two consecutive PMD mappings for FDT early scan */
pa = dtb_pa & ~(PMD_SIZE - 1);
create_pmd_mapping(early_dtb_pmd, DTB_EARLY_BASE_VA,
pa, PMD_SIZE, PAGE_KERNEL);
create_pmd_mapping(early_dtb_pmd, DTB_EARLY_BASE_VA + PMD_SIZE,
pa + PMD_SIZE, PMD_SIZE, PAGE_KERNEL);
dtb_early_va = (void *)DTB_EARLY_BASE_VA + (dtb_pa & (PMD_SIZE - 1));
#else /* CONFIG_BUILTIN_DTB */
#ifdef CONFIG_64BIT
/*
* __va can't be used since it would return a linear mapping address
* whereas dtb_early_va will be used before setup_vm_final installs
* the linear mapping.
*/
dtb_early_va = kernel_mapping_pa_to_va(XIP_FIXUP(dtb_pa));
#else
dtb_early_va = __va(dtb_pa);
#endif /* CONFIG_64BIT */
#endif /* CONFIG_BUILTIN_DTB */
#else
#ifndef CONFIG_BUILTIN_DTB
/* Create two consecutive PGD mappings for FDT early scan */
pa = dtb_pa & ~(PGDIR_SIZE - 1);
create_pgd_mapping(early_pg_dir, DTB_EARLY_BASE_VA,
pa, PGDIR_SIZE, PAGE_KERNEL);
create_pgd_mapping(early_pg_dir, DTB_EARLY_BASE_VA + PGDIR_SIZE,
pa + PGDIR_SIZE, PGDIR_SIZE, PAGE_KERNEL);
dtb_early_va = (void *)DTB_EARLY_BASE_VA + (dtb_pa & (PGDIR_SIZE - 1));
#else /* CONFIG_BUILTIN_DTB */
#ifdef CONFIG_64BIT
dtb_early_va = kernel_mapping_pa_to_va(XIP_FIXUP(dtb_pa));
#else
dtb_early_va = __va(dtb_pa);
#endif /* CONFIG_64BIT */
#endif /* CONFIG_BUILTIN_DTB */
#endif
riscv: Fix memblock reservation for device tree blob This fixes an error with how the FDT blob is reserved in memblock. An incorrect physical address calculation exposed the FDT header to unintended corruption, which typically manifested with of_fdt_raw_init() faulting during late boot after fdt_totalsize() returned a wrong value. Systems with smaller physical memory sizes more frequently trigger this issue, as the kernel is more likely to allocate from the DMA32 zone where bbl places the DTB after the kernel image. Commit 671f9a3e2e24 ("RISC-V: Setup initial page tables in two stages") changed the mapping of the DTB to reside in the fixmap area. Consequently, early_init_fdt_reserve_self() cannot be used anymore in setup_bootmem() since it relies on __pa() to derive a physical address, which does not work with dtb_early_va that is no longer a valid kernel logical address. The reserved[0x1] region shows the effect of the pointer underflow resulting from the __pa(initial_boot_params) offset subtraction: [ 0.000000] MEMBLOCK configuration: [ 0.000000] memory size = 0x000000001fe00000 reserved size = 0x0000000000a2e514 [ 0.000000] memory.cnt = 0x1 [ 0.000000] memory[0x0] [0x0000000080200000-0x000000009fffffff], 0x000000001fe00000 bytes flags: 0x0 [ 0.000000] reserved.cnt = 0x2 [ 0.000000] reserved[0x0] [0x0000000080200000-0x0000000080c2dfeb], 0x0000000000a2dfec bytes flags: 0x0 [ 0.000000] reserved[0x1] [0xfffffff080100000-0xfffffff080100527], 0x0000000000000528 bytes flags: 0x0 With the fix applied: [ 0.000000] MEMBLOCK configuration: [ 0.000000] memory size = 0x000000001fe00000 reserved size = 0x0000000000a2e514 [ 0.000000] memory.cnt = 0x1 [ 0.000000] memory[0x0] [0x0000000080200000-0x000000009fffffff], 0x000000001fe00000 bytes flags: 0x0 [ 0.000000] reserved.cnt = 0x2 [ 0.000000] reserved[0x0] [0x0000000080200000-0x0000000080c2dfeb], 0x0000000000a2dfec bytes flags: 0x0 [ 0.000000] reserved[0x1] [0x0000000080e00000-0x0000000080e00527], 0x0000000000000528 bytes flags: 0x0 Fixes: 671f9a3e2e24 ("RISC-V: Setup initial page tables in two stages") Signed-off-by: Albert Ou <aou@eecs.berkeley.edu> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-09-28 07:14:18 +08:00
dtb_early_pa = dtb_pa;
/*
* Bootime fixmap only can handle PMD_SIZE mapping. Thus, boot-ioremap
* range can not span multiple pmds.
*/
BUILD_BUG_ON((__fix_to_virt(FIX_BTMAP_BEGIN) >> PMD_SHIFT)
!= (__fix_to_virt(FIX_BTMAP_END) >> PMD_SHIFT));
#ifndef __PAGETABLE_PMD_FOLDED
/*
* Early ioremap fixmap is already created as it lies within first 2MB
* of fixmap region. We always map PMD_SIZE. Thus, both FIX_BTMAP_END
* FIX_BTMAP_BEGIN should lie in the same pmd. Verify that and warn
* the user if not.
*/
fix_bmap_spmd = fixmap_pmd[pmd_index(__fix_to_virt(FIX_BTMAP_BEGIN))];
fix_bmap_epmd = fixmap_pmd[pmd_index(__fix_to_virt(FIX_BTMAP_END))];
if (pmd_val(fix_bmap_spmd) != pmd_val(fix_bmap_epmd)) {
WARN_ON(1);
pr_warn("fixmap btmap start [%08lx] != end [%08lx]\n",
pmd_val(fix_bmap_spmd), pmd_val(fix_bmap_epmd));
pr_warn("fix_to_virt(FIX_BTMAP_BEGIN): %08lx\n",
fix_to_virt(FIX_BTMAP_BEGIN));
pr_warn("fix_to_virt(FIX_BTMAP_END): %08lx\n",
fix_to_virt(FIX_BTMAP_END));
pr_warn("FIX_BTMAP_END: %d\n", FIX_BTMAP_END);
pr_warn("FIX_BTMAP_BEGIN: %d\n", FIX_BTMAP_BEGIN);
}
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
}
#if defined(CONFIG_64BIT) && defined(CONFIG_STRICT_KERNEL_RWX)
void __init protect_kernel_linear_mapping_text_rodata(void)
{
unsigned long text_start = (unsigned long)lm_alias(_start);
unsigned long init_text_start = (unsigned long)lm_alias(__init_text_begin);
unsigned long rodata_start = (unsigned long)lm_alias(__start_rodata);
unsigned long data_start = (unsigned long)lm_alias(_data);
set_memory_ro(text_start, (init_text_start - text_start) >> PAGE_SHIFT);
set_memory_nx(text_start, (init_text_start - text_start) >> PAGE_SHIFT);
set_memory_ro(rodata_start, (data_start - rodata_start) >> PAGE_SHIFT);
set_memory_nx(rodata_start, (data_start - rodata_start) >> PAGE_SHIFT);
}
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
static void __init setup_vm_final(void)
{
uintptr_t va, map_size;
phys_addr_t pa, start, end;
arch, drivers: replace for_each_membock() with for_each_mem_range() There are several occurrences of the following pattern: for_each_memblock(memory, reg) { start = __pfn_to_phys(memblock_region_memory_base_pfn(reg); end = __pfn_to_phys(memblock_region_memory_end_pfn(reg)); /* do something with start and end */ } Using for_each_mem_range() iterator is more appropriate in such cases and allows simpler and cleaner code. [akpm@linux-foundation.org: fix arch/arm/mm/pmsa-v7.c build] [rppt@linux.ibm.com: mips: fix cavium-octeon build caused by memblock refactoring] Link: http://lkml.kernel.org/r/20200827124549.GD167163@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Baoquan He <bhe@redhat.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Daniel Axtens <dja@axtens.net> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Emil Renner Berthing <kernel@esmil.dk> Cc: Hari Bathini <hbathini@linux.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: https://lkml.kernel.org/r/20200818151634.14343-13-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-14 07:58:08 +08:00
u64 i;
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
/**
* MMU is enabled at this point. But page table setup is not complete yet.
* fixmap page table alloc functions should be used at this point
*/
pt_ops.alloc_pte = alloc_pte_fixmap;
pt_ops.get_pte_virt = get_pte_virt_fixmap;
#ifndef __PAGETABLE_PMD_FOLDED
pt_ops.alloc_pmd = alloc_pmd_fixmap;
pt_ops.get_pmd_virt = get_pmd_virt_fixmap;
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
/* Setup swapper PGD for fixmap */
create_pgd_mapping(swapper_pg_dir, FIXADDR_START,
__pa_symbol(fixmap_pgd_next),
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
PGDIR_SIZE, PAGE_TABLE);
/* Map all memory banks in the linear mapping */
arch, drivers: replace for_each_membock() with for_each_mem_range() There are several occurrences of the following pattern: for_each_memblock(memory, reg) { start = __pfn_to_phys(memblock_region_memory_base_pfn(reg); end = __pfn_to_phys(memblock_region_memory_end_pfn(reg)); /* do something with start and end */ } Using for_each_mem_range() iterator is more appropriate in such cases and allows simpler and cleaner code. [akpm@linux-foundation.org: fix arch/arm/mm/pmsa-v7.c build] [rppt@linux.ibm.com: mips: fix cavium-octeon build caused by memblock refactoring] Link: http://lkml.kernel.org/r/20200827124549.GD167163@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Baoquan He <bhe@redhat.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Daniel Axtens <dja@axtens.net> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Emil Renner Berthing <kernel@esmil.dk> Cc: Hari Bathini <hbathini@linux.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Stafford Horne <shorne@gmail.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: https://lkml.kernel.org/r/20200818151634.14343-13-rppt@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-14 07:58:08 +08:00
for_each_mem_range(i, &start, &end) {
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
if (start >= end)
break;
if (start <= __pa(PAGE_OFFSET) &&
__pa(PAGE_OFFSET) < end)
start = __pa(PAGE_OFFSET);
map_size = best_map_size(start, end - start);
for (pa = start; pa < end; pa += map_size) {
va = (uintptr_t)__va(pa);
create_pgd_mapping(swapper_pg_dir, va, pa,
map_size,
#ifdef CONFIG_64BIT
PAGE_KERNEL
#else
PAGE_KERNEL_EXEC
#endif
);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
}
}
#ifdef CONFIG_64BIT
/* Map the kernel */
create_kernel_page_table(swapper_pg_dir, PMD_SIZE);
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
/* Clear fixmap PTE and PMD mappings */
clear_fixmap(FIX_PTE);
clear_fixmap(FIX_PMD);
/* Move to swapper page table */
csr_write(CSR_SATP, PFN_DOWN(__pa_symbol(swapper_pg_dir)) | SATP_MODE);
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
local_flush_tlb_all();
/* generic page allocation functions must be used to setup page table */
pt_ops.alloc_pte = alloc_pte_late;
pt_ops.get_pte_virt = get_pte_virt_late;
#ifndef __PAGETABLE_PMD_FOLDED
pt_ops.alloc_pmd = alloc_pmd_late;
pt_ops.get_pmd_virt = get_pmd_virt_late;
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
}
#else
asmlinkage void __init setup_vm(uintptr_t dtb_pa)
{
dtb_early_va = (void *)dtb_pa;
dtb_early_pa = dtb_pa;
}
static inline void setup_vm_final(void)
{
}
#endif /* CONFIG_MMU */
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
#ifdef CONFIG_STRICT_KERNEL_RWX
void __init protect_kernel_text_data(void)
{
unsigned long text_start = (unsigned long)_start;
unsigned long init_text_start = (unsigned long)__init_text_begin;
unsigned long init_data_start = (unsigned long)__init_data_begin;
unsigned long rodata_start = (unsigned long)__start_rodata;
unsigned long data_start = (unsigned long)_data;
unsigned long max_low = (unsigned long)(__va(PFN_PHYS(max_low_pfn)));
set_memory_ro(text_start, (init_text_start - text_start) >> PAGE_SHIFT);
set_memory_ro(init_text_start, (init_data_start - init_text_start) >> PAGE_SHIFT);
set_memory_nx(init_data_start, (rodata_start - init_data_start) >> PAGE_SHIFT);
/* rodata section is marked readonly in mark_rodata_ro */
set_memory_nx(rodata_start, (data_start - rodata_start) >> PAGE_SHIFT);
set_memory_nx(data_start, (max_low - data_start) >> PAGE_SHIFT);
}
void mark_rodata_ro(void)
{
unsigned long rodata_start = (unsigned long)__start_rodata;
unsigned long data_start = (unsigned long)_data;
set_memory_ro(rodata_start, (data_start - rodata_start) >> PAGE_SHIFT);
debug_checkwx();
}
#endif
#ifdef CONFIG_KEXEC_CORE
/*
* reserve_crashkernel() - reserves memory for crash kernel
*
* This function reserves memory area given in "crashkernel=" kernel command
* line parameter. The memory reserved is used by dump capture kernel when
* primary kernel is crashing.
*/
static void __init reserve_crashkernel(void)
{
unsigned long long crash_base = 0;
unsigned long long crash_size = 0;
unsigned long search_start = memblock_start_of_DRAM();
unsigned long search_end = memblock_end_of_DRAM();
int ret = 0;
/*
* Don't reserve a region for a crash kernel on a crash kernel
* since it doesn't make much sense and we have limited memory
* resources.
*/
#ifdef CONFIG_CRASH_DUMP
if (is_kdump_kernel()) {
pr_info("crashkernel: ignoring reservation request\n");
return;
}
#endif
ret = parse_crashkernel(boot_command_line, memblock_phys_mem_size(),
&crash_size, &crash_base);
if (ret || !crash_size)
return;
crash_size = PAGE_ALIGN(crash_size);
if (crash_base == 0) {
/*
* Current riscv boot protocol requires 2MB alignment for
* RV64 and 4MB alignment for RV32 (hugepage size)
*/
crash_base = memblock_find_in_range(search_start, search_end,
crash_size, PMD_SIZE);
if (crash_base == 0) {
pr_warn("crashkernel: couldn't allocate %lldKB\n",
crash_size >> 10);
return;
}
} else {
/* User specifies base address explicitly. */
if (!memblock_is_region_memory(crash_base, crash_size)) {
pr_warn("crashkernel: requested region is not memory\n");
return;
}
if (memblock_is_region_reserved(crash_base, crash_size)) {
pr_warn("crashkernel: requested region is reserved\n");
return;
}
if (!IS_ALIGNED(crash_base, PMD_SIZE)) {
pr_warn("crashkernel: requested region is misaligned\n");
return;
}
}
memblock_reserve(crash_base, crash_size);
pr_info("crashkernel: reserved 0x%016llx - 0x%016llx (%lld MB)\n",
crash_base, crash_base + crash_size, crash_size >> 20);
crashk_res.start = crash_base;
crashk_res.end = crash_base + crash_size - 1;
}
#endif /* CONFIG_KEXEC_CORE */
#ifdef CONFIG_CRASH_DUMP
/*
* We keep track of the ELF core header of the crashed
* kernel with a reserved-memory region with compatible
* string "linux,elfcorehdr". Here we register a callback
* to populate elfcorehdr_addr/size when this region is
* present. Note that this region will be marked as
* reserved once we call early_init_fdt_scan_reserved_mem()
* later on.
*/
static int __init elfcore_hdr_setup(struct reserved_mem *rmem)
{
elfcorehdr_addr = rmem->base;
elfcorehdr_size = rmem->size;
return 0;
}
RESERVEDMEM_OF_DECLARE(elfcorehdr, "linux,elfcorehdr", elfcore_hdr_setup);
#endif
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
void __init paging_init(void)
{
setup_bootmem();
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
setup_vm_final();
}
void __init misc_mem_init(void)
{
early_memtest(min_low_pfn << PAGE_SHIFT, max_low_pfn << PAGE_SHIFT);
arch_numa_init();
sparse_init();
RISC-V: Setup initial page tables in two stages Currently, the setup_vm() does initial page table setup in one-shot very early before enabling MMU. Due to this, the setup_vm() has to map all possible kernel virtual addresses since it does not know size and location of RAM. This means we have kernel mappings for non-existent RAM and any buggy driver (or kernel) code doing out-of-bound access to RAM will not fault and cause underterministic behaviour. Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e. MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e. 516 KB) of memory for initial page tables which is never freed. The memory required for initial page tables will further increase if we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000) This patch implements two-staged initial page table setup, as follows: 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in a early page table (i.e. early_pg_dir). The early_pg_dir will be used only by boot HART so it can be freed as-part of init memory free-up. 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM banks in the final page table (i.e. swapper_pg_dir). The boot HART will start using swapper_pg_dir at the end of setup_vm_final(). All non-boot HARTs directly use the swapper_pg_dir created by boot HART. We have following advantages with this new approach: 1. Kernel mappings for non-existent RAM don't exists anymore. 2. Memory consumed by initial page tables is now indpendent of the chosen PAGE_OFFSET. 3. Memory consumed by initial page tables on RV64 system is 2 pages (i.e. 8 KB) which has significantly reduced and these pages will be freed as-part of the init memory free-up. The patch also provides a foundation for implementing strict kernel mappings where we protect kernel text and rodata using PTE permissions. Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> [paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-06-29 04:36:21 +08:00
zone_sizes_init();
#ifdef CONFIG_KEXEC_CORE
reserve_crashkernel();
#endif
memblock_dump_all();
}
#ifdef CONFIG_SPARSEMEM_VMEMMAP
int __meminit vmemmap_populate(unsigned long start, unsigned long end, int node,
struct vmem_altmap *altmap)
{
mm/sparsemem: enable vmem_altmap support in vmemmap_populate_basepages() Patch series "arm64: Enable vmemmap mapping from device memory", v4. This series enables vmemmap backing memory allocation from device memory ranges on arm64. But before that, it enables vmemmap_populate_basepages() and vmemmap_alloc_block_buf() to accommodate struct vmem_altmap based alocation requests. This patch (of 3): vmemmap_populate_basepages() is used across platforms to allocate backing memory for vmemmap mapping. This is used as a standard default choice or as a fallback when intended huge pages allocation fails. This just creates entire vmemmap mapping with base pages (PAGE_SIZE). On arm64 platforms, vmemmap_populate_basepages() is called instead of the platform specific vmemmap_populate() when ARM64_SWAPPER_USES_SECTION_MAPS is not enabled as in case for ARM64_16K_PAGES and ARM64_64K_PAGES configs. At present vmemmap_populate_basepages() does not support allocating from driver defined struct vmem_altmap while trying to create vmemmap mapping for a device memory range. It prevents ARM64_16K_PAGES and ARM64_64K_PAGES configs on arm64 from supporting device memory with vmemap_altmap request. This enables vmem_altmap support in vmemmap_populate_basepages() unlocking device memory allocation for vmemap mapping on arm64 platforms with 16K or 64K base page configs. Each architecture should evaluate and decide on subscribing device memory based base page allocation through vmemmap_populate_basepages(). Hence lets keep it disabled on all archs in order to preserve the existing semantics. A subsequent patch enables it on arm64. Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Tested-by: Jia He <justin.he@arm.com> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: Will Deacon <will@kernel.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Michal Hocko <mhocko@suse.com> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Hsin-Yi Wang <hsinyi@chromium.org> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Paul Mackerras <paulus@samba.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Steve Capper <steve.capper@arm.com> Cc: Yu Zhao <yuzhao@google.com> Link: http://lkml.kernel.org/r/1594004178-8861-1-git-send-email-anshuman.khandual@arm.com Link: http://lkml.kernel.org/r/1594004178-8861-2-git-send-email-anshuman.khandual@arm.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-08-07 14:23:19 +08:00
return vmemmap_populate_basepages(start, end, node, NULL);
}
#endif