.\" -*- nroff -*- .\" Copyright 1993, 1994, 1995 by Theodore Ts'o. All Rights Reserved. .\" This file may be copied under the terms of the GNU Public License. .\" .TH MKE2FS 8 "@E2FSPROGS_MONTH@ @E2FSPROGS_YEAR@" "E2fsprogs version @E2FSPROGS_VERSION@" .SH NAME mke2fs \- create an ext2/ext3 filesystem .SH SYNOPSIS .B mke2fs [ .B \-c | .B \-l .I filename ] [ .B \-b .I block-size ] [ .B \-f .I fragment-size ] [ .B \-g .I blocks-per-group ] [ .B \-i .I bytes-per-inode ] [ .B \-I .I inode-size ] [ .B \-j ] [ .B \-J .I journal-options ] [ .B \-N .I number-of-inodes ] [ .B -n ] [ .B \-m .I reserved-blocks-percentage ] [ .B \-o .I creator-os ] [ .B \-O .IR feature [,...] ] [ .B \-q ] [ .B \-r .I fs-revision-level ] [ .B \-E .I extended-options ] [ .B \-v ] [ .B \-F ] [ .B \-L .I volume-label ] [ .B \-M .I last-mounted-directory ] [ .B \-S ] [ .B \-T .I filesystem-type ] [ .B \-V ] .I device [ .I blocks-count ] @JDEV@.sp @JDEV@.B "mke2fs \-O journal_dev" @JDEV@[ @JDEV@.B \-b @JDEV@.I block-size @JDEV@] .\" No external-journal specific journal options yet (size is ignored) .\" @JDEV@[ .\" @JDEV@.B \-J .\" @JDEV@.I journal-options .\" @JDEV@] @JDEV@[ @JDEV@.B \-L @JDEV@.I volume-label @JDEV@] @JDEV@[ @JDEV@.B \-n @JDEV@] @JDEV@[ @JDEV@.B \-q @JDEV@] @JDEV@[ @JDEV@.B \-v @JDEV@] @JDEV@.I external-journal @JDEV@[ @JDEV@.I blocks-count @JDEV@] .SH DESCRIPTION .B mke2fs is used to create an ext2/ext3 filesystem (usually in a disk partition). .I device is the special file corresponding to the device (e.g .IR /dev/hdXX ). .I blocks-count is the number of blocks on the device. If omitted, .B mke2fs automagically figures the file system size. If called as .B mkfs.ext3 a journal is created as if the .B \-j option was specified. .SH OPTIONS .TP .BI \-b " block-size" Specify the size of blocks in bytes. Valid block size vales are 1024, 2048 and 4096 bytes per block. If omitted, .B mke2fs block-size is heuristically determined by the file system size and the expected usage of the filesystem (see the .B \-T option). If .I block-size is negative, then .B mke2fs will use heuristics to determine the appropriate block size, with the constraint that the block size will be at least .I block-size bytes. This is useful for certain hardware devices which require that the blocksize be a multiple of 2k. .TP .B \-c Check the device for bad blocks before creating the file system. If this option is specified twice, then a slower, read-write test is used instead of a fast read-only test. .TP .BI \-E " extended-options" Set extended options for the filesystem. Extended options are comma separated, and may take an argument using the equals ('=') sign. The .B -E option used to be .B -R in earlier versions of .BR mke2fs . The .B -R option is still accepted for backwards compatibility. The following extended options are supported: .RS 1.2i .TP .BI stride= stripe-size Configure the filesystem for a RAID array with .I stripe-size filesystem blocks per stripe. .TP .BI resize= max-online-resize Reserve enough space so that the block group descriptor table can grow to support a filesystem that has max-online-resize blocks. .RE .TP .BI \-f " fragment-size" Specify the size of fragments in bytes. .TP .B \-F Force .B mke2fs to create a filesystem, even if the specified device is not a partition on a block special device, or if other parameters do not make sense. In order to force .B mke2fs to create a filesystem even if the filesystem appears to be in use or is mounted (a truly dangerous thing to do), this option must be specified twice. .TP .BI \-g " blocks-per-group" Specify the number of blocks in a block group. There is generally no reason the user to ever set this parameter, as the default is optimal for the filesystem. (For administrators who are creating filesystems on RAID arrays, it is preferable to use the .I stride RAID parameter as part of the .B \-R option rather than manipulating the number of blocks per group.) This option is generally used by developers who are developing test cases. .TP .BI \-i " bytes-per-inode" Specify the bytes/inode ratio. .B mke2fs creates an inode for every .I bytes-per-inode bytes of space on the disk. The larger the .I bytes-per-inode ratio, the fewer inodes will be created. This value generally shouldn't be smaller than the blocksize of the filesystem, since then too many inodes will be made. Be warned that is not possible to expand the number of inodes on a filesystem after it is created, so be careful deciding the correct value for this parameter. .TP .BI \-I " inode-size" Specify the size of each inode in bytes. .B mke2fs creates 128-byte inodes by default. In kernels after 2.6.10 and some earlier vendor kernels it is possible to utilize larger inodes to store extended attributes for improved performance. The .I inode-size value must be a power of two larger or equal to 128. The larger the .I inode-size the more space the inode table will consume, and this reduces the usable space in the filesystem and can also negatively impact performance. Using the default value is always safe, though it may be desirable to use 256-byte inodes if full backward compatibility is not a concern. Extended attributes stored in large inodes are not visible with older kernels, and such filesystems will not be mountable with 2.4 kernels at all. It is not possible to change this value after the filesystem is created. .TP .B \-j Create the filesystem with an ext3 journal. If the .B \-J option is not specified, the default journal parameters will be used to create an appropriately sized journal (given the size of the filesystem) stored within the filesystem. Note that you must be using a kernel which has ext3 support in order to actually make use of the journal. .TP .BI \-J " journal-options" Create the ext3 journal using options specified on the command-line. Journal options are comma separated, and may take an argument using the equals ('=') sign. The following journal options are supported: .RS 1.2i .TP .BI size= journal-size Create an internal journal (i.e., stored inside the filesystem) of size .I journal-size megabytes. The size of the journal must be at least 1024 filesystem blocks (i.e., 1MB if using 1k blocks, 4MB if using 4k blocks, etc.) and may be no more than 102,400 filesystem blocks. @JDEV@.TP @JDEV@.BI device= external-journal @JDEV@Attach the filesystem to the journal block device located on @JDEV@.IR external-journal . @JDEV@The external @JDEV@journal must already have been created using the command @JDEV@.IP @JDEV@.B mke2fs -O journal_dev @JDEV@.I external-journal @JDEV@.IP @JDEV@Note that @JDEV@.I external-journal @JDEV@must have been created with the @JDEV@same block size as the new filesystem. @JDEV@In addition, while there is support for attaching @JDEV@multiple filesystems to a single external journal, @JDEV@the Linux kernel and @JDEV@.BR e2fsck (8) @JDEV@do not currently support shared external journals yet. @JDEV@.IP @JDEV@Instead of specifying a device name directly, @JDEV@.I external-journal @JDEV@can also be specified by either @JDEV@.BI LABEL= label @JDEV@or @JDEV@.BI UUID= UUID @JDEV@to locate the external journal by either the volume label or UUID @JDEV@stored in the ext2 superblock at the start of the journal. Use @JDEV@.BR dumpe2fs (8) @JDEV@to display a journal device's volume label and UUID. See also the @JDEV@.B -L @JDEV@option of @JDEV@.BR tune2fs (8). .RE @JDEV@.IP @JDEV@Only one of the @JDEV@.BR size " or " device @JDEV@options can be given for a filesystem. .TP .BI \-l " filename" Read the bad blocks list from .IR filename . Note that the block numbers in the bad block list must be generated using the same block size as used by mke2fs. As a result, the .B \-c option to .B mke2fs is a much simpler and less error-prone method of checking a disk for bad blocks before formatting it, as .B mke2fs will automatically pass the correct parameters to the .B badblocks program. .TP .BI \-L " new-volume-label" Set the volume label for the filesystem to .IR new-volume-label . The maximum length of the volume label is 16 bytes. .TP .BI \-m " reserved-blocks-percentage" Specify the percentage of the filesystem blocks reserved for the super-user. This avoids fragmentation, and allows root-owned daemons, such as .BR syslogd (8), to continue to function correctly after non-privileged processes are prevented from writing to the filesystem. The default percentage is 5%. .TP .B \-M Set the last mounted directory for the filesystem. This might be useful for the sake of utilities that key off of the last mounted directory to determine where the filesystem should be mounted. .TP .B \-n causes mke2fs to not actually create a filesystem, but display what it would do if it were to create a filesystem. This can be used to determine the location of the backup superblocks for a particular filesystem, so long as the mke2fs parameters that were passed when the filesystem was originally created are used again. (With the .B \-n option added, of course!) .TP .BI \-N " number-of-inodes" overrides the default calculation of the number of inodes that should be reserved for the filesystem (which is based on the number of blocks and the .I bytes-per-inode ratio). This allows the user to specify the number of desired inodes directly. .TP .BI \-o " creator-os" Manually override the default value of the "creator os" field of the filesystem. Normally the creator field is set by default to the native OS of the .B mke2fs executable. .TP .B "\-O \fIfeature\fR[,...]" Create filesystem with given features (filesystem options), overriding the default filesystem options. The default features which are enabled by default are specified by the .I base_features relation, either in the .I [libdefaults] section in the .B /etc/mke2fs.conf configuration file, or in the subsection of the .I [fs_types] section for the filesystem type as specified by the .B -T option. The filesystem type-specific configuration setting found in the .I [fs_types] section will override the global default found in .IR [libdefaults] . .sp The filesystem feature set will be further edited using either the feature set specification specified by this option, or if this option is not specified, by the .I default_features relation for the filesystem type being created, or in the .I [libdefaults] section of the configuration file. .sp The filesystem feature set is comprised of a list of features, separated by commas, that are to be enabled. To disable a feature, simply prefix the feature name with a caret ('^') character. The pseudo-filesystem feature "none" will clear all filesystem features. .RS 1.2i .TP .B dir_index Use hashed b-trees to speed up lookups in large directories. .TP .B filetype Store file type information in directory entries. .TP .B has_journal Create an ext3 journal (as if using the .B \-j option). @JDEV@.TP @JDEV@.B journal_dev @JDEV@Create an external ext3 journal on the given device @JDEV@instead of a regular ext2 filesystem. @JDEV@Note that @JDEV@.I external-journal @JDEV@must be created with the same @JDEV@block size as the filesystems that will be using it. .TP .B resize_inode Reserve space so the block group descriptor table may grow in the future. Useful for online resizing using .BR resize2fs . By default .B mke2fs will attempt to reserve enough space so that the filesystem may grow to 1024 times its initial size. This can be changed using .B resize extended option. .TP .B sparse_super Create a filesystem with fewer superblock backup copies (saves space on large filesystems). .RE .TP .B \-q Quiet execution. Useful if .B mke2fs is run in a script. .TP .BI \-r " revision" Set the filesystem revision for the new filesystem. Note that 1.2 kernels only support revision 0 filesystems. The default is to create revision 1 filesystems. .TP .B \-S Write superblock and group descriptors only. This is useful if all of the superblock and backup superblocks are corrupted, and a last-ditch recovery method is desired. It causes .B mke2fs to reinitialize the superblock and group descriptors, while not touching the inode table and the block and inode bitmaps. The .B e2fsck program should be run immediately after this option is used, and there is no guarantee that any data will be salvageable. It is critical to specify the correct filesystem blocksize when using this option, or there is no chance of recovery. .\" .TP .\" .BI \-t " test" .\" Check the device for bad blocks before creating the file system .\" using the specified test. .TP .BI \-T " fs-type" Specify how the filesystem is going to be used, so that .B mke2fs can choose optimal filesystem parameters for that use. The filesystem types that are can be supported are defined in the configuration file .BR /etc/mke2fs.conf (5). The default configuration file contains definitions for the filesystem types: small, floppy, news, largefile, and largefile4. .TP .B \-v Verbose execution. .TP .B \-V Print the version number of .B mke2fs and exit. .SH AUTHOR This version of .B mke2fs has been written by Theodore Ts'o . .SH BUGS .B mke2fs accepts the .B \-f option but currently ignores it because the second extended file system does not support fragments yet. .br There may be other ones. Please, report them to the author. .SH AVAILABILITY .B mke2fs is part of the e2fsprogs package and is available from http://e2fsprogs.sourceforge.net. .SH SEE ALSO .BR mke2fs.conf (5), .BR badblocks (8), .BR dumpe2fs (8), .BR e2fsck (8), .BR tune2fs (8)